Replacement Swivel Mount for Fulton 1500 XLT Jack

Question

Question:

will it work for Fulton 1500 jack

asked by: Dennis

0

Expert Reply:

I spoke with my contact at Fulton and the Jack Mounting Bracket # P9012-00 could be used as a weld-on mounting bracket for the Fulton Swivel Trailer Jack # FXPD15L that you referenced.

expert reply by: Jameson C

0

Answer 1

There is indeed a replacement hardware/bushing kit available. You'd need part #F0933325S00. My Fulton representative confirms that this would be the correct replacement bushing for your Fulton Magnum 1500 lb capacity jack.

view full answer...

Answer 2

Thank you for providing the picture of your existing mount. This was helpful to idenfication and I have attached it to this post. As you mentioned, the 90 degree snap in holes are 3" apart from center to center. It may be helpful to note that…

view full answer...

Answer 3

The Fulton Adapter Kit #F500320 will allow you to mount a Fulton F2 trailer jack to your current mounting bracket like part #P9012-00. The Wide Wheel #F1413040134 version of the F2 works on gravel. It will obviously be harder to move on gravel than…

view full answer...

Answer 4

Could you possibly get me the brand of landing gear that you have? It's nearly impossible to pick out the gear kit based on dimensions of the bevels but with more info that can help narrow down the search.

view full answer...

Answer 5

It sure will! The Replacement Hardware Kit for Fulton Swivel Jack #F0933325S00 were looking at is confirmed to fit your older Fulton Magnum Swivel Jack made back in roughly 2006. This was confirmed by my contact at Fulton. I included a video of the…

view full answer...

Answer 6

I do not see something we carry that would be an exact replacement. If you can give me your jack's model number it would help me find if we have something that will work for you because the replacement mounting brackets match up to certain…

view full answer...

Answer 7

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 8

I've never heard of an actual third brake light connector on a camper shell to plug in on a truck and we don't carry any parts to do that. The light generally needs to be hardwired into the truck's brake light circuit. The issue with this…

view full answer...

Answer 9

If your current springs have 5 leaves then going to a 7 leaf spring will increase the height of the trailer a little and make the trailer more susceptible to sway. Regarding capacity if you go with springs rated higher than what is required it will…

view full answer...

Answer 10

The manual lockout on your Atwood 85778 surge brake coupler is there so that you can back up the trailer without the brakes locking up on you. Yes you can safely tow your trailer with the broken manual lockout, you just have to make sure you…

view full answer...

Answer 11

Since you have a wheelbase/axle spacing of 38 inches the correct hanger kit for slipper springs would be the part #HAP-105-205-01. And then for a 7k trailer axle the u-bolt kit you'd want would be the part #APUBR-8. I attached the diagram to use…

view full answer...

Answer 12

To tow your trailer that uses an RV style 7-way blade style connector with your semi that has a 7-pin connector, you need to construct an adapter that will also combine the brake signal into the right and left directional signal pins. This can be…

view full answer...

Replacement Swivel Mount for Fulton 1500 XLT Jack

Products Referenced in This Question

Product Page this Question was Asked From

Continue Researching