Swagman Cable Lock S2005 to Use with Swagman Shinook S64683

Question

Question:

Since the Swagman Shinook part number S64683 comes with a lock to secure to your hitch, will the cable, part number S2005, fit. I know there is a unit that comes with cable and lock, part number S64031. Does make since to purchase a second lock to secure to your hitch. Can you verify. Thanks

asked by: Fred A

0

Expert Reply:

Yes, since the Swagman Chinook 2 Bike Platform Rack # S64683 comes with the hitch pin lock you can upgrade the setup to also having a cable lock as well with part # S2005.

expert reply by: Jameson C

0

Answer 1

Yes, the Swagman Chinook 2 Bike Platform Rack #S64683 has the threaded locking hitch pin which is supposed to reduce the rattle in the hitch receiver. I recommend trying to install the threaded hitch pin without installing the bike rack into your…

view full answer...

Answer 2

The Curt Trailer Hitch, #13514, is a Class III trailer hitch with a 2 inch receiver so you will need a 5/8 inch diameter pin just like you suggested. For a standard pin and clip, we have #PC3 or #C21510. For a locking pin we have the Trailer Hitch…

view full answer...

Answer 3

Yes, the Swagman Chinook part #S64683 that you referenced can fold up when not in use. If you check out the picture I attached you can see it folded.

view full answer...

Answer 4

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 5

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 6

There is only one difference between the Curt Trailer Hitch Receiver #C13176 and etrailer Trailer Hitch Receiver #e98909 that fit your 2020 Chevrolet Colorado, which is the finish. The Curt trailer hitch has a glossy black finish while the etrailer…

view full answer...

Answer 7

Class I and Class II hitches both have a 1-1/4 inch receiver opening. The difference is that a Class I hitch has a lower tongue weight rating, usually 200 pounds and a lower towing rating, usually 2,000 pounds. A Class II hitch usually has a tongue…

view full answer...

Answer 8

To me it makes the most sense to put a Bike Rack #HLY64FR on the flat towed vehicle rather than above the tow bars. Especially on heavy e-bikes as they are difficult to lift that high onto the rack, but also as it only makes sense to have the rack…

view full answer...

Answer 9

To add a class III hitch to your 2024 Honda CR-V hybrid, I recommend the Curt Trailer Hitch item #C13397. This hitch is custom fit and bolts to your CR-V with included hardware. It is a class III hitch with a 2" receiver. I really like this…

view full answer...

Answer 10

The Kuat NV 2.0 2 Bike Platform Rack, #NV22G, and the Kuat NV 2.0 Base 2-Bike Platform rack, #BA22B. are both very similar bike racks. Both racks can be expanded to a 4-bike rack, #NA22G add-on for the NV 2.0 and #BA02B for the NV 2.0 Base, and both…

view full answer...

Answer 11

I would discourage the use of an adapter for use of 2 inch accessories in 1-1/4 inch trailer hitch receivers. The reason is that the adapter places the carrier farther away from the rear of the vehicle and hitch, creating additional torque that 1-1/4…

view full answer...

Answer 12

Yes, you can install a Curt Trailer Hitch Receiver #C11433 on your 2019 Chevrolet Spark. This receiver is capable of supporting up to 200lbs of tongue weight. With each of the Lectric 3.0 e-bikes weighing roughly 60lbs without the battery you will…

view full answer...

Swagman Cable Lock S2005 to Use with Swagman Shinook S64683

Products Referenced in This Question

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching