How Does the Plunger on the Lubrimatic Mini Grease Gun Lock When Loading a Grease Cartridge?

Question

Question:

how does the plunger lock? 30132 lubrimatic

asked by: Ron

0

Expert Reply:

The plunger on the Lubrimatic Mini Grease Gun locks much like a caulking gun. To load the grease cartridge, you would pull the plunger fully to the rear, and pull it slightly to the side so that the detent in the plunger handle catches on the end of the cap. This grease gun is very simple to operate, and is the perfect size for storing in your tool box.

expert reply by: Mike L

0

Answer 1

You are correct that in the Blue Ox SwayPro Owner's Manual they do recommend use molybdenum grease on both the hitch ball and the spring bars. The LubriMatic Moly EP Grease #LM54FR in a grease gun, such as #L30480, will work well. You could use…

view full answer...

Answer 2

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 3

Yes, the Curt hitch part #C77ZV is a fit for the 2023 Toyota Crown Hybrid. I attached a link to the install instructions as well as a link to an installer finder in case you wanted to find someone near you to install the hitch.

view full answer...

Answer 4

For sag from towing a trailer the best recommendation I can make is actually a weight distribution system. Suspension enhancement will help level your truck while towing. But the advantage to a weight distribution system is that it levels the vehicle…

view full answer...

Answer 5

Thank you for purchasing from etrailer! You did a great job selecting compatible parts. When using Leaf Springs #e64SR with the #AP233 Equalizer Kit and the #H248 Hanger Kit, there should be 29-1/2" between the front and center hangers and…

view full answer...

Answer 6

The manual lockout on your Atwood 85778 surge brake coupler is there so that you can back up the trailer without the brakes locking up on you. Yes you can safely tow your trailer with the broken manual lockout, you just have to make sure you…

view full answer...

Answer 7

To tow your trailer that uses an RV style 7-way blade style connector with your semi that has a 7-pin connector, you need to construct an adapter that will also combine the brake signal into the right and left directional signal pins. This can be…

view full answer...

Answer 8

I agree it is the right time to upgrade to a Lithium charger/converter as not all are Lithium compatible. I recommend using the Progressive Dynamics Mighty Mini AC/DC Panel and Converter/Smart Charger - 60 Amp #PD4060K which is a replacement for your…

view full answer...

Answer 9

The 40 amp fuse for your 2006 Chevrolet Silverado tow package is used for the 12 volt battery charge circuit. This fuse is located toward the front of the underhood fuse box closest to the front auxiliary positive post (see photo). There may be a…

view full answer...

Answer 10

On a 2005 Chevy Silverado 1500, If you are facing the front of the truck looking at the power distribution box, there will be a post at the back left side and a fuse slot near it. It is that fuse slot that you will install a 30 amp fuse. I have…

view full answer...

Answer 11

For your AL-KO 7210 braking assembly, you can use the Hydraulic Brake Kit #AKFBBRK-7 as a replacement. These braking assemblies measure 12" x 2", bolts onto a 5 bolt mounting flange, will work with wheel sizes from 14-1/2" to…

view full answer...

Answer 12

I do have an option for you but we have not yet gotten out hands on a 2019 Chevrolet Blazer therefore, have not had the chance to look for the brake controller wiring port either. I checked with both Tekonsha and Curt and it looks like they have not…

view full answer...

How Does the Plunger on the Lubrimatic Mini Grease Gun Lock When Loading a Grease Cartridge?

Products Referenced in This Question

Continue Researching