Trailer Frame Mounting Space Required for Installing Timbren Axle-Less Suspension System ASR5200S04
Question:
can I mount this axle directly to 2x3 x 3/16 trailer frame member... bolt or weld or should I fab a mounting..? Do you have a PDF of axle mounting area.... trailer has 18 deck and will haul 3000# car typically.
asked by: Tim R
Expert Reply:
The Timbren Axle-Less Trailer Suspension System # ASR5200S04 that you referenced will require a trailer frame area of at least 14-5/16" inches long and about 3" tall for proper mounting. I have attached a dimensional diagram below with this and other measurements labeled for the setup (just note that the spindle measurement isn't correct since this model features a 4" drop). When mounting to the frame it's extremely important to use all 3 bolt holes provided, so this full length is needed.
It sounds like the area you have picked out on the trailer is a bit too small, unless I'm not understanding correctly. If you can send me a picture of what space you are referring to on the trailer or give me a little more detail on what yo have in mind I will be happy to help you further.
I have attached an install video as well that you can use for reference.
Product Page this Question was Asked From
Timbren Axle-Less Trailer Suspension - Standard Duty - 4" Drop - 5 Bolt Flange - 5,200 lbs
- Trailer Axles
- Rubber Spring Suspension
- Easy Lube Spindles
- 5200 lbs
- Spindles Only
- Universal Fit
- Drop - 4 Inch
- Timbren
more information >
Featured Help Information
Instructions
Miscellaneous Media
Continue Researching
- Shop: Timbren Axle-Less Trailer Suspension - Standard Duty - 4" Drop - 5 Bolt Flange - 5,200 lbs
- Search Results: military discounts
- Shop: Easy Grease Trailer Idler Hub Assembly for 6K Axles - 6 on 5-1/2 - Pre-Greased
- Shop: Timbren Silent Ride Suspension for Single Axle Trailers w/ 2" Square Axles - 2,000 lbs
- Shop: Trailer Axle w/ Electric Brakes - Easy Grease - 6 on 5-1/2 Bolt Pattern - 89" Long - 5,200 lbs
- Shop: etrailer Electric Trailer Brakes - Self-Adjusting - 12" - Left/Right Hand - 5.2K to 7K
- Shop: #42 E-Z Lube Spindle w/ Flange for 5.2K to 7K Trailer Axles - 2-1/4" Diameter
- Search Results: 42655uc1
- Shop: Demco Trailer Coupler - Flat Plate Mount - eZ-Latch - Black - 2-5/16" Ball - 21,000 lbs
- Article: RV Sway Control, Stabilization, and Suspension Enhancement
- Article: How to Measure a Trailer Axle
- Search Results: 235/85r16
- Q&A: Replacement 5,200 Lb Axle for a Hudson Trailer
- Q&A: Recommended Replacement 4" Drop Axle Rated for 5,200 lbs
- Q&A: Replacement Axle Solution for 1989 Avion Travel Trailer
- Q&A: Drum-Less Hub for Timbren Axle-Less Trailer Suspension System and 17 Inch Wheels
- Video: Timbren Axle-Less Trailer Suspension System Installation
- Video: Timbren Axle-Less Trailer Suspension System Test Course
- Video: Dexter Axle Trailer Hubs and Drums - Hub with Integrated Drum - 42866UC3 Review
- Search Results: trailer drop axle
- Q&A: What Is The Angle For The etrailer A-Frame Trailer Coupler?
- Article: How to Choose a Trailer Hitch Coupler
- Article: Most Popular Wheel Bearings
- Q&A: Dexter vs. etrailer 7,000 lb Electric Trailer Brakes
- Article: Where to Position the Trailer Axle?
- Article: Trailer Wiring Diagrams
- Q&A: Will etrailer EZ Lube Hub AKHD-655-6-EZ-K Fit an AL/KO Axle Rated for 4400 Pounds
- Article: Brake Controller 7- and 4-Way Installation Kit (ETBC7)