What is Pilot Diameter of Dexter 8k Hub with 8 on 6-1/2 inch Bolt Pattern

Question

Question:

What is the flange size Diameter of the hub8-287-14UC1? thanks

asked by: Cristian G

0

Expert Reply:

The pilot diameter or flange diameter of the Dexter trailer hub part # 8-287-14UC1 is 4-3/4 inches. So the wheel you'd install on this hub would need to have a pilot diameter of at least 4-3/4 inches to fit over it.

I attached a review video for this hub for you to check out as well.

expert reply by: Jameson C

0

Answer 1

I checked around our inventory and while we do not have what you're looking for, however we still may have an option for you. Since we do not have the wheel studs you're looking for, my best advice is to replace the entire hub that already…

view full answer...

Answer 2

The torque for the Dexter Trailer Hub and Drum Assembly - 6,000-lb and 7,000-lb Axles - 12" - 5 Spoke Utility #8-174-5UC3 is not specified by the manufacturer. For 9/16 inch studs, the typical lug nut torque will be 120-140 ft lbs based on most…

view full answer...

Answer 3

In order to use 17.5" diameter trailer wheels you'll need to upgrade to 9/16" lug studs. There are no other options as all wheels this size use this size or larger since they are designed for more weight. In order to do this you'll…

view full answer...

Answer 4

You can't use conical/tapered lug nuts like the #12CLN on wheels with flat bolt seats; instead you'll want to use a lug nut with a flange like the Flange Wheel Nut - 5/8" #95188. If you can tell me which wheels you've got and the lug…

view full answer...

Answer 5

At the end of the day, you can use any of those options (stainless steel, zinc or chrome), you just need to get a lug nut that fits the 9/16 stud. But, we do not have a chrome option that fits the 9/16 stud. Personally, I would go with the stainless…

view full answer...

Answer 6

The manual lockout on your Atwood 85778 surge brake coupler is there so that you can back up the trailer without the brakes locking up on you. Yes you can safely tow your trailer with the broken manual lockout, you just have to make sure you…

view full answer...

Answer 7

Due to the fact that carbon fiber bikes have a more sensitive frame, Thule does recommend using the Thule UpRide #TH599000. Bike rack technology has not changed to make the racks less compatible, but carbon fiber bikes have become increasingly…

view full answer...

Answer 8

The Demco Hijacker Autoslide 21K #DM8550038 weighs approximately 305-lbs. The head of this hitch weighs around 70-lbs and can be removed to help make moving and installing this 5th wheel hitch a little bit easier.

view full answer...

Answer 9

I really wish we had replacement parts still for the Atwood couplers but since they've been out of business for so long we don't have any way to get the parts you are wanting.

view full answer...

Answer 10

Since you have a wheelbase/axle spacing of 38 inches the correct hanger kit for slipper springs would be the part #HAP-105-205-01. And then for a 7k trailer axle the u-bolt kit you'd want would be the part #APUBR-8. I attached the diagram to use…

view full answer...

Answer 11

For all intents and purposes, yes, the Fulton drop leg stabilizer jack SJL80300 is the same as the square leg jack you asked about: - Square Drop Leg Stabilizer Jack - 18" Travel - 2,000 lbs #SJ-R208 Different manufacturers but otherwise they…

view full answer...

Answer 12

In general the amount of articulation travel/play when going from an empty to a maximum load with 12,000 pound Dexter Torflex Axles will be about 2 inches in height and less than an inch in length. I have attached a chart and diagram that goes into…

view full answer...

What is Pilot Diameter of Dexter 8k Hub with 8 on 6-1/2 inch Bolt Pattern

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching