How to Get 12 Volt Power For Installation of a Prodigy Brake Controller on a 2011 GMC Yukon Denali
Question:
2011 GMC Denali.wired Prodigy unit to 4 wires under dash but there is no power to unit. Is there a fuse or relay that I need to add in fusebox. Car is new,no fuses blown. How do I get power to prodigy? I've been to GMC and a hitch retailer with no answers.
asked by: Tom L
Expert Reply:
The wiring to power the brake controller on your 2011 GMC Yukon Denali is under the hood on the driver side next to the fender well. Remove the cover for the power distribution box and you will find the wire taped to a harness between the fender well and power distribution box. We have an FAQ article that details this, see link, and I added a photo that I took of the wire locations on a GM pickup.
You may also have to connect the 12 volt power wire for your 7-Way trailer connector. Our article details where this wire is and where to connect it also. The attached photo shows this wire location too.
To attach these wires you will need one M6 x 1.0 nut, # 185916, and one M8 x 1.25 nut, # 185917, to secure these wires to the appropriate power stud at the front of the power distribution box.
There is a possibility that you will need to install a 30 amp fuse for the brake controller and a 40 amp fuse for the 12 volt power supply at the locations closest to the power studs in the power distribution box. For the 2011 model these are the larger square type fuses and are available at a local auto parts store. The legend under the lid of the box details where these fuses go, and I attached a photo showing their location for you also.
Products Referenced in This Question
Zinc Plated Hex Flange Nut - M6
- Accessories and Parts
- Trailer Brake Controller
- Hardware
- Nuts
- Hex Nut
- Flint Hill Goods
more information >
Product Page this Question was Asked From
Zinc Plated Hex Flange Nut - M8
- Accessories and Parts
- Trailer Brake Controller
- Hardware
- Nuts
- Hex Nut
- Flint Hill Goods
more information >
Continue Researching
- Shop: Hopkins Engager Push-To-Test Trailer Breakaway Kit w/ Built-In Charger - Side Load - 7" Wire
- Shop: Replacement Box with LED Lid for Engager Breakaway Kit
- Search Results: led turn signal
- Video: Optronics LED Trailer Tail Lights with Grommet and Pigtails Review
- Shop: Optronics LED Trailer Tail Light - Stop, Turn, Tail - Submersible - 10 Diode - Oval - Red Lens
- Article: Breakaway Kit Installation for Single and Dual Brake Axle Trailers
- Article: Towing a Trailer? Let's Talk About Brake Controllers
- Article: Brake Controller 7- and 4-Way Installation Kit (ETBC7)
- Article: Installing an Electric Brake Controller on 2007-2013 GM Full-Size Truck or 2007-Present GM SUV
- Q&A: How to Wire Electric Brakes on a Tandem Axle Trailer
- Q&A: What Size Nuts Are Needed to Connect Wires Under Hood for Brake Controller Installation on GMC Yukon
- Q&A: How Does a Brake Controller Install in a 2012 Chevy Silverado
- Q&A: Is 8 inches From Bottom of Weight Distribution System to Ground Enough Clearance
- Q&A: Diameter of Holes on Fastway e2 Weight Distribution Shank part # FA92-02-4214
- Q&A: Shank with 4 Inch Drop for Trunnion Weight Distribution System
- Q&A: Will a Fastway Weight Distribution Shank Work with a Reese WD System
- Article: Trailer Wiring Diagrams
- Article: Brake Controller Installation for 2007 (New Body Style) - 2013 GMC Sierra and Chevy Silverado
- Article: Brake Controller Installation: Starting from Scratch