Tips to Improve Voltage Drop from Trailer Connector to Back to the Rear Light Assemblies
Question:
I recently purchased an observation camera for my travel trailer. The camera company is telling me that the camera isn’t working because it’s not getting enough voltage. Apparently their cameras need 12.4 volts or greater in order to work properly. So, when I check the voltage at the factory installed “camera ready” location, it’s only getting 12.0 volts. The trailer is supposedly wired such that the camera power is tied to the running lights. I’ve confirmed that the nearby running lights, as well as those at the front of the trailer, are all getting the same 12.0-12.2 volts. I’ve also confirmed that the truck is putting out approximately 13.6-13.8 volts at the 7 pin trailer harness connection point. The truck is running with the headlights and running lights on. The problem exists whether the trailer is hitched tongue on ball or not. What am I missing? Where could the 1.5 volts be going?
asked by: John R
Expert Reply:
I'm not sure I totally believe that the problem is a lack of voltage. It's possible this is the case, but12 volts should easily power a camera designed for a standard 12 volt system. I would recommend taking the camera up near the vehicle battery and try powering the camera straight from the battery as this is where the voltage would be the highest. If the camera works here then it is voltage related. If not, then the camera is most likely defective.
Now the reason for the voltage loss is the resistance from the length of wire between the trailer connector and the rear of the vehicle. Only way to improve this would be to go with a heavier gauge wire here.
Product Page this Question was Asked From
- Trailer Wiring
- Trailer Connectors
- Trailer End Connector
- 0 - 5 Feet Long
- Plug and Lead
- 4 Flat
- Draw-Tite
more information >
Continue Researching
- Shop: Replacement Front Jack for Lippert Ground Control 3.0 Leveling System
- Shop: Hook Probe Circuit Tester
- Video: Performance Tool Hook Probe Circuit Tester Review
- Q&A: What is a Good Replacement for the Wesbar 105826?
- Video: Optronics Trailer Lights - Clearance Lights - MCL93RB Review
- Video: Optronics Thinline Amber LED Clearance and Side Marker Light Installation
- Search Results: wire connectors
- Search Results: boat trailer light kit
- Search Results: boat trailer wire harness
- Video: Optronics LED Identification Light Bar Installation
- Search Results: wesbar
- Shop: Trailer Wiring Junction Box - 7 Color Coded Terminals - ABS
- Video: Review of Furrion RV Camera System - 7 Way Power Adapter - FR87PR
- Shop: Optronics LED Combination Trailer Tail Lights - Submersible - 40 Diodes - Driver and Passenger Side
- Shop: Mounting Bracket for Optronics A91, AL82, AL90, AL91, or AL191 Series Lights - Open Back - Black
- Shop: Optronics LED Clearance or Side Marker Light - Submersible - 3 Diodes - Rectangle - Amber Lens
- Shop: Optronics Trailer Clearance and Side Marker Light - Submersible - Rectangle - Amber Lens
- Video: B and W Companion OEM 5th Wheel Hitch Installation - 2020 Chevrolet Silverado 2500 BWRVK3710
- Q&A: Troubleshooting Voltage Drop When Connecting LED Trailer Lights to Wiring Harness
- Article: 5 Things to Know About Weight Distribution Hitches
- Q&A: Why Trailer Wiring Carries Low and Higher Voltage on the Light Circuits
- Q&A: How to Wire a Solar Panel to Two 12 Volt Batteries Connected in Parallel on RV
- Search Results: dc to dc charger
- Video: Voyager RV Backup Camera Systems 12V PWM Filter Installation - 2020 Mercedes-Benz Sprinter 3500
- Q&A: What Part Can I Use to Get Constant 12v Camera Power with My VueSMART RV Camera # HM34FR?
- Q&A: Installation of 12V PWM Filter for RV Backup Camera Systems on GM Vehicles
- Q&A: No Power To Cameras On Travel Trailer With Furrion Camera System Using 2021 GMC
- Search Results: furrion 7 way
- Search Results: furrion 7 way adapter
- Article: How to Charge a Trailer Battery While Driving: 3 Common Problems (And How to Fix Them)