Installing Bearing Buddy Grease Seal Set # BB60005
Question:
The 1 3/8 stainless steel seal ring how does it fit over the the worn area on spindle, if it’s pitted and leaks but is not undersize? What is the inner dia of ring that goes over the worn seal area on spindle?
asked by: Ron
Expert Reply:
The inner stainless steel ring included with the Spindle Grease Seal Set # BB60005 has an inside diameter of 1.0645 inches (and an outside diameter of 1.375 inches).
This ring is designed to install on the spindle for the grease seal to ride on once the hub is in place. I have attached a great installation video that shows exactly how each piece from the kit is installed. This setup allows for free movement and reduced leakage for a longer-lasting seal. It is not however meant to repair a damaged spindle.
If the spindles on your trailer are pitted and leaking then I highly recommend replacing them altogether. I have attached a link that will take you to our available selection that you can look through.
Product Page this Question was Asked From
Spindle Grease Seal Set for L44649 Inner Bearing and 1.980 Bearing Buddy
- Trailer Bearings Races Seals Caps
- Seals
- Grease Seals - Double Lip
- 1.375 Inch I.D.
- 1.98 Inch O.D.
- Bearing Buddy
more information >
Featured Help Information
Miscellaneous Media
Continue Researching
- Video: Bearing Buddy Trailer Bearings Races Seals Caps - Seals - BB60011 Review
- Shop: Bright Way Push-to-Test Trailer Breakaway Kit with 1-Amp Charger and 5 Ah Battery - Side Load
- Shop: Bright Way Push-to-Test Trailer Breakaway Kit with 1-Amp Charger and 5 Ah Battery - Top Load
- Shop: Ventline E-Z Lift Ventadome Trailer Roof Vent - Manual Lift - 14-1/4" x 14-1/4" - White
- Search Results: door hold open
- Search Results: brake control
- Search Results: side vents
- Search Results: 3802308
- Shop: Performance Chip Tuners
- Shop: Cold Air Intake
- Shop: Exhaust
- Shop: Air Filter
- Search Results: fender lights
- Video: Review of CE Smith Trailer Hubs and Drums - Hub - CE13315
- Search Results: 72" fender
- Shop: Trailer Axle Beam with Easy Grease Spindles - 95" Long - 7,000 lbs
- Video: Review of Timken Trailer Bearings Races - L44649 and L44610 Set - TMK23VR
- Shop: CE Smith Trailer Idler Hub Assembly w/ Case for 2.7K Axles - 5 on 4-1/2 - Galvanized - Pre-Greased
- Shop: Spindle Grease Seal Set for L44649 Inner Bearing and 1.980 Bearing Buddy
- Q&A: Replacing Short Hubs On A 1996 EZ Loader Trailer With Straight Spindles
- Video: Dexter Trailer Hub and Drum Assembly Installation 42866UC3-EZ
- Shop: CE Smith Trailer Hub Assembly w/ Carrying Case for 2,700-lb Axles - 5 on 4-1/2 - Pre-Greased
- Search Results: e88gr
- Q&A: Replacing Trailer Axle Spindle From Older Short Spindle To BTR E-Z Lube Spindle
- Q&A: Replacement Bearing Solution for DICO Hub 45263
- Q&A: How to Pick Out Replacement Hubs for a Boat Trailer
- Q&A: Looking for Hub to Replace Dico # 45263
- Q&A: Replacement Hubs, Wheels, and Tires for a Boat Trailer That Uses Dico 45263 Hubs
- Q&A: Can I Use Hubs with 3500-lb Capacity on Axle with 1750-lb Capacity If The Bearings Match Up?
- Video: Fulton Trailer Winch - Standard Hand Winch - F142401 Review