Disc Brake Kit Recommendation for 2003 Ranger Trail Trailer
Question:
I have a 2003 ranger trail trailer that has the old ufp gold oil bath hubs on them. the inner seal is 21333 tb, inner bearing is 25580, outer bearing is lm67048. The spindle measures 1.75 inner and 1.248 outer. I am looking for the hub and rotor replacement the closest parts that I see have the 25580 inner and the 15123 outer bearing sold separately and I am not sure exactly what inner seal I need. bolt pattern is 6 on 5.5 1/2-20 studs and it is a 12inch rotor. I see the 15123 outer bearing has the same I.D. as the lm67048 Is the Kodiak hub KHR12D the correct replacement hub and will the 15123 bearing kit work with this? It is going on a boat trailer. replacing all of the parts I would be looking at the parts for the Inner seals, bearings, hubs with rotors which this listing states the races are already installed, and bearing buddies.
asked by: Jamie D
Expert Reply:
The grease seal you have has the inner diameter of 2.125 and is basically a # GS-2125DL. So what you'd need to do is use the grease seal # GS-2125DL with the correct bearings for this kit of # 25580 and # 15123 and you'd be set. These bearings and seals would be all that you'd need to fit the hub/rotor kit to your axle.
Products Referenced in This Question
Replacement Trailer Hub Bearing - 15123
- Trailer Bearings Races Seals Caps
- Bearings
- Standard Bearings
- 1.250 Inch I.D.
- Bearing 15123
- Race 15245
- 5200 lbs Axle
- 6000 lbs Axle
- 7000 lbs Axle
- etrailer
more information >
Replacement Trailer Hub Bearing - 25580
- Trailer Bearings Races Seals Caps
- Bearings
- Standard Bearings
- 1.750 Inch I.D.
- Bearing 25580
- Race 25520
- 10000 lbs Axle
- 6000 lbs Axle
- 7000 lbs Axle
- 8000 lbs Axle
- 9000 lbs Axle
- etrailer
more information >
Grease Seal - Double Lip - 2.125" ID - 3.376" OD - GS-2125DL
- Trailer Bearings Races Seals Caps
- Seals
- Grease Seals - Double Lip
- 2.125 Inch I.D.
- 3.376 Inch O.D.
- etrailer
more information >
Product Page this Question was Asked From
Kodiak 12" Hub-and-Rotor Assembly - 6 on 5-1/2 - Dacromet - 5,200 lbs to 6,000 lbs
- Trailer Hubs and Drums
- Hub with Integrated Rotor
- Standard
- 25580
- 15123
- For 5200 lbs Axles
- For 6000 lbs Axles
- 1/2 Inch Stud
- 6 on 5-1/2 Inch
- 15 Inch Wheel
- 16 Inch Wheel
- 16-1/2 Inch Wheel
- Kodiak
more information >
Continue Researching
- Q&A: Replacement for Dexter 8-283 Hub/Drum
- Q&A: Recommended Replacement Converter for a Elixir ELX-45
- Article: How to Bleed Your Trailer Surge Brakes
- Q&A: How To Install the Spindle Nut on a 12,000 Pound Dexter Axle
- Q&A: Comparing Dexter DX, BrakeRite II, and Hydrastar Electric-Over-Hydraulic Actuators
- Q&A: How to Correctly Position Ramp Door Spring for Installation
- Q&A: Parts Needed to Flat Tow a 2022 Jeep Wrangler Rubicon
- Q&A: Where is Brake Controller Install Port in 2014 Nissan Titan
- Article: How to Measure Your Trailer Wheel Bolt Pattern
- Article: How Much Does a Boat and Trailer Weigh?
- Article: Wiring Trailer Lights with a 7-Way Plug (It's Easier Than You Think)
- Article: Double-Eye Trailer Suspension System Review
- Article: How to Raise Your Travel Trailer Height
- Article: How to Measure for Trailer Hitch Drop