Can the Access LED Tailgate Light Bar # A90148 be Cut to Fit

Question

Question:

Can it be cut to fit?

asked by: Troy B

0

Expert Reply:

I spoke with my contact at Access who said that you should be able to cut the LED Tailgate Light Bar # A90148 to fit your specific application but it wouldn't be covered under warranty if the light were to no longer work. The unit is also sealed so you would need to reseal the end that you cut to ensure that the elements stay out of the unit.

expert reply by: Jon G

0

Answer 1

I've linked you to the installation instruction for the Rampage LED Tailgate Light Bar. The light bar features a 4-pole flat trailer connector that would plug into the existing 4 pole trailer connector on the vehicle. The wiring harness has an…

view full answer...

Answer 2

Access LED Tailgate Light Bar #A90148 is used in conjunction with reverse lights but it doesn't replace them. On a vehicle you need to have a reverse light on each side of the rear of the vehicle. A single light in the center, even a long one…

view full answer...

Answer 3

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 4

That's not surprising. Some bike racks are rated to be used behind a towed vehicle or trailer but not most. Also, it wasn't until recently that a lot of the rack manufacturers started giving a yay or nay on a towed vehicle. Most have taken…

view full answer...

Answer 5

The Hopkins Custom Tail Light Wiring Kit for Towed Vehicles part #HM56202 will not work on your 1997 Jeep Wrangler TJ because Jeep changed the pinouts on the tail lights between the 1997 and 1998 model years. Therefore, it will plug into the…

view full answer...

Answer 6

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 7

You will need the Red LED Trailer Clearance or Side Marker Light #328-K-52 or Amber LED Trailer Clearance or Side Marker Light #328-K-51 for your 2018 Forest River Sunseeker motorhome. These lenses have the same Top Command SAE-AP2-16 markings on the…

view full answer...

Answer 8

Since Demco uses 3,500 drum brake assemblies part #DMSB24429M and #DMSB24428M what you'd need is similar 3,500 electric brake assemblies like the etrailer part #AKEBRK-35L-SA for the left hand side and #AKEBRK-35R-SA for the right hand side. To…

view full answer...

Answer 9

If you are needing the hub and drum assembly then you will want to go with the Dexter Trailer Hub and Drum Assembly #8-201-5UC3-EZ but if you are just looking for an idler hub then you will want part #8-213-5UC1 instead. These come with the correct…

view full answer...

Answer 10

If you are installing just the Firestone Ride-Rite kit, #F2400, and not also adding an on-board air compressor such as #F2158, then I would estimate that it should take about 2 hours to install the kit. That is for someone with some mechanical…

view full answer...

Answer 11

When installing/adjusting the Solera RV Slide-Out Awning #LCV000163285 tension is applied by rotating the awning roller 14 times. This should apply the needed spring tension so that the fabric doesn't billow in the wind or leave enough slack that…

view full answer...

Answer 12

If your old axles have a 5 bolt brake flange the assemblies like Dexter Electric Trailer Brake Assembly - 12" - Left Hand - 6,000 lbs part #23-105 or Dexter Electric Trailer Brake Assembly - 12" - Right Hand - 6,000 lbs part #23-106 will…

view full answer...

Can the Access LED Tailgate Light Bar # A90148 be Cut to Fit

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching