Which Way Does Roadmaster Reflex Install on 2018 Ford F-53

Question

Question:

I have purchased the RSSA-22 for my 2018 F53. It appears that the tie rod bracket gets bolted the bottom of the tie rod. Im not sure if the piston end sits on top or bottom of the tie rod bracket. Ive watched different videos and many seem to be different. Thanks.

asked by: William B

1

Helpful Expert Reply:

I attached a picture that shows the correct orientation for the Roadmaster Reflex Steering Stabilizer # RM-RBK22-RSSA and how it should install on your 2018 Ford F-53 motorhome chassis.

expert reply by: Jameson C

1

click to enlarge

Answer 1

I attached a picture that I took from the install instructions for the Roadmaster Reflex Steering Stabilizer part #RM-RBK25 that you referenced to thist page.

view full answer...

Answer 2

The correct steering stabilizer for your 2012 Coachmen Mirada, which was built on a Ford F-53 chassis, is the Roadmaster Reflex Steering Stabilizer with Mounting Brackets for Class A Motor Homes #RM-RBK22-RSSA. I confirmed this with the manufacturer…

view full answer...

Answer 3

The correct Roadmaster Reflex mounting brackets for a 2021 Fleetwood Bounder 35P would be the part #RM-RBK25.

view full answer...

Answer 4

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 5

If you are needing the hub and drum assembly then you will want to go with the Dexter Trailer Hub and Drum Assembly #8-201-5UC3-EZ but if you are just looking for an idler hub then you will want part #8-213-5UC1 instead. These come with the correct…

view full answer...

Answer 6

The old version of the #HBA-CAM used 4 wires, but the product was updated awhile back and now uses only two wires as shown in the photo on the product description page. The white wire from the HBA-CAM would tap into the white ground wire and the blue…

view full answer...

Answer 7

When installing/adjusting the Solera RV Slide-Out Awning #LCV000163285 tension is applied by rotating the awning roller 14 times. This should apply the needed spring tension so that the fabric doesn't billow in the wind or leave enough slack that…

view full answer...

Answer 8

The 40 amp fuse for your 2006 Chevrolet Silverado tow package is used for the 12 volt battery charge circuit. This fuse is located toward the front of the underhood fuse box closest to the front auxiliary positive post (see photo). There may be a…

view full answer...

Answer 9

On a 2005 Chevy Silverado 1500, If you are facing the front of the truck looking at the power distribution box, there will be a post at the back left side and a fuse slot near it. It is that fuse slot that you will install a 30 amp fuse. I have…

view full answer...

Answer 10

The number you provided, "7753400" is a patent number which corelates to the Equalizer for E-Z Flex Suspension part #013-144-03. This is for a single equalizer but if you need the entire kit it's the Dexter E-Z Flex Suspension Kit part…

view full answer...

Answer 11

For your enclosed trailer application I have several suggestions for adding interior lighting that you can control directly via a switch. Since your current 4-pole trailer wiring does NOT include a 12V auxiliary power feed that could power inside…

view full answer...

Answer 12

The only way you could power interior dome lights on a trailer without it being connected to a tow vehicle would be to power the lights with a battery like a breakaway battery. How you choose to wire up the batteries will in the end be up to you, but…

view full answer...

Which Way Does Roadmaster Reflex Install on 2018 Ford F-53

Product Page this Question was Asked From

Featured Help Information

Instructions

Miscellaneous Media

Continue Researching