Recommended Suspension Enhancement for 2008 Toyota Sequoia with Integrated Auto Leveling System

Question

Question:

Hello, my ‘08 Toyota Sequoia has an auto leveling system but I want to add a heavy bumper, winch, etc to overland and would like to upgrade my shocks/struts/springs but can’t find any that don’t say “won’t work with auto leveling system”. Can you help or have any advice?

asked by: Emily M

0

Expert Reply:

For your 2008 Toyota Sequoia with auto leveling system, the air spring kits will not fit because they require the same location as your auto leveling system. I do however have a solution to help you with the load when adding the bumper and winch and that is the Timbren Rear Suspension Enhancement System # TTORSEQ1. This system will not interfere with your auto leveling, but will replace your factory bump stops. They simply are mounted to the bump stop location and will provide additional support under the load so your factory system doesn't take the toll.

It will help compensate for off-center loads and reduce body roll. It will take the brunt of the road shock and extend the life of your factory system.

expert reply by: Jason S

0

Answer 1

Your 2008 Toyota Sequoia will not be raised at all when you install the Timbren system that fits, which is the following part number: - Timbren Rear Suspension Enhancement System #TTORSEQ1 When installed, the #TTORSEQ1 will have a gap between the…

view full answer...

Answer 2

We do have the Rhino-Rack Masterkey Lock Barrels #RRRK093-2 which will provide you with 2 new lock cores and keys for your Rhino-Rack Zenith MasterFit Rooftop Cargo Box #RRRMFZ66. As far as pricing goes on the different sets they can change based on…

view full answer...

Answer 3

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 4

The best option we offer for your dump trailer is the Erickson Mesh Tarp and Truck Bed Cover part #EM57059 which measures 12' wide x 16' long. It's not the exact dimensions you wanted but it will still cover most of the area you need it…

view full answer...

Answer 5

For a standard replacement equalizer for your Dexter 13-122 equalizers you'd want the #TREQE1 or for a cushioned version you'd want the part #K71-653-00 which comes with new shackles and bolts. For a kit that includes new bolts, bushings, and…

view full answer...

Answer 6

For sag from towing a trailer the best recommendation I can make is actually a weight distribution system. Suspension enhancement will help level your truck while towing. But the advantage to a weight distribution system is that it levels the vehicle…

view full answer...

Answer 7

You will need the Red LED Trailer Clearance or Side Marker Light #328-K-52 or Amber LED Trailer Clearance or Side Marker Light #328-K-51 for your 2018 Forest River Sunseeker motorhome. These lenses have the same Top Command SAE-AP2-16 markings on the…

view full answer...

Answer 8

That spindle looks pretty well destroyed so best option is going to be to replace the axle. You are going to need to measure your current axles in a few places to get the correct one as we don't have access to what your numbers reference. You…

view full answer...

Answer 9

Generally speaking, the lube plate will need to cover the skid plate on the 5th wheel hitch. There are some pin boxes out there that will recommend a specific lube plate but most of the times this classification will be from the 5th wheel hitch…

view full answer...

Answer 10

If the two 6 volt batteries were wired in series to produce 12 volts total then a 12 volt battery would easily work as a replacement for them. If the two batteries were wired in parallel and the output voltage is 6 volts then no. I attached a diagram…

view full answer...

Answer 11

Yes, you will need the Thule universal change key, #853-1251, to remove and install new lock cores. the change key pulls down all the tumblers so the lock can be removed or inserted. The existing lock, if present, will have to be unlocked for the…

view full answer...

Answer 12

To see all of the correct wheel and tire combos you'd need check out the link I attached. The option I would recommend is the part #TA43RR which is a Load Range C tire size ST175/80R13 mounted on a white spoke wheel with a bolt pattern of 5 on…

view full answer...

Recommended Suspension Enhancement for 2008 Toyota Sequoia with Integrated Auto Leveling System

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching