Dimensions of the Roadmaster Comfort Ride Slipper Spring System
Question:
Id like to be sure that this will work on my trailer before I purchase. Therefore I have some questions that could get me closer to that determination. 1 What is the inside width of the Center Box? 2 What are the dimensions of the cutout in the top of center box that current hanger is to go through? 3 What is the max.-min. measurement that will work as far as top of center-box to center of center-hanger bolt hole that will work. I see in the pictures that it is a slot, rather than a hole.
asked by: Shawn
Helpful Expert Reply:
I went out to our warehouse and measured one of the Roadmaster Comfort Ride Slipper Spring System like part # RM-2460-2570 for you. The box is 3-1/4" wide and the opening is 3-3/4" long x 2-3/4" wide. I have attached a photo of these measurements for you as well.
According to my contact at Roadmaster, the center leaf spring hanger will need to be between 3" - 3-1/2" from the bottom of the frame to the center of the bolt hole. If the hanger you have will not work with these measurements you can use the Leaf Spring Hanger part # 28-5.
Products Referenced in This Question
Front/Center/Rear Hanger for Double-Eye Springs - 3-1/4" Tall - 9/16" Bolt Hole
- Trailer Suspension Parts
- Hangers
- Boat Trailer
- Camper
- Car Hauler
- Snowmobile Trailer
- Utility Trailer
- Double Eye Springs
- 9/16 Inch Diameter
- 3-1/4 Inch Tall
- Single Axle
- Tandem Axle
- Triple Axle
- etrailer
more information >
Product Page this Question was Asked From
Roadmaster Comfort Ride Leaf Spring Suspension Kit w/ Shock Absorbers - Tandem 7K Trailer Axles
- Trailer Suspension Parts
- Equalizer Upgrade Kit
- Leaf Spring Replacement System
- Suspension Kits
- Boat Trailer
- Camper
- Car Hauler
- Snowmobile Trailer
- Utility Trailer
- 7000 lbs
- Round Axle - 3 Inch
- Tandem Axle
- Roadmaster
more information >
Featured Help Information
Instructions
Continue Researching
- Shop: Roadmaster Comfort Ride Leaf Spring Suspension Kit w/ Shock Absorbers - Tandem 7K Trailer Axles
- Shop: Roadmaster Comfort Ride Leaf Spring Suspension Kit w/ Shock Absorbers - Tandem 5K Trailer Axles
- Shop: Trailer Wiring
- Shop: Roadmaster Comfort Ride Leaf Spring Suspension Kit w/ Shocks - Tandem 8K, 3-1/2" Axles
- Shop: Roadmaster Comfort Ride Shock Absorbers for Tandem Axle Trailers - 5,200-lb to 7,000-lb Axle
- Shop: Roadmaster Comfort Ride Shock Absorbers for Tandem Axle Trailers - 3,500-lb Axle
- Q&A: Can I Use the Roadmaster Comfort Ride with Shocks on Axles 33 Inches Apart
- Shop: Roadmaster Comfort Ride Leaf Spring Suspension Kit w/ Shocks - Tandem 8K, 3" Trailer Axles
- Shop: MORryde 14-3/4" Shock Absorbing Equalizers for Tandem Axle Trailers w/ 42" Wheelbase - 8K
- Article: How to Choose a High-Low Adapter
- Q&A: Wiring Configuration of Mighty Cord 7-Way Plug A10-7W10
- Q&A: Will the Roadmaster RM-2460-2570 replace 25 1/4" Leaf Springs Without Modifications?
- Video: 3 Inch Round Trailer U-Bolts Installation
- Q&A: Does a Trailer with Two 3,500 Pound Axles have a Gross Capacity of 7,000 Pounds
- Q&A: Dimensions for the Roadmaster Comfort Ride Leaf Spring Suspension Kit w/ Shock Absorbers
- Search Results: roadmaster 2560
- Video: Roadmaster Comfort Ride Shock Absorbers Installation - 2020 Grand Design Imagine Travel Trailer
- Q&A: Recommended Suspension Enhancement For A 2019 Grand Design Reflection 150 Fifth Wheel
- Q&A: Axle Center Spacing When Installing The 7,000LB Roadmaster Comfort Ride Leaf Spring Suspension Kit
- Search Results: road armor
- Video: Roadmaster Comfort Ride Shock Absorbers Installation - 2017 Grand Design Solitude Fifth Wheel
- Video: Roadmaster Comfort Ride Leaf Spring Suspension Kit Installation - 2021 Grand Design Reflection Fifth
- Search Results: spare tire covers
- Search Results: tire covers
- Video: Timbren Silent Ride Suspension Review
- Search Results: 7 pin connector
- Shop: Tailgate
- Shop: Truck Bed Tailgate Assist
- Shop: Suspension Enhancement
- Video: EZ Connector Custom Fit Vehicle Wiring - Trailer Hitch Wiring - 319-R7-02D Review