Determining Clearance Needed for MaxxFan Deluxe Roof Vent # MA00-07500K
Question:
I have a skylight near where I will be installing the fan. How much clearance is required on all sides of the Maxx Air MA00-07500K?
asked by: John P
Expert Reply:
The MaxxFan Deluxe Roof Vent w/ 12V Fan # MA00-07500K referenced in your question fits a 14 inch x 14 inch RV roof opening, but the mounting flange itself measures 16-1/2 inches x 16-1/2 inches. This will refer to the footprint of the unit from inside your RV/trailer.
The actual vent that will mount above the roof of the trailer measures 22-1/2 inches long and 16-1/2 inches wide. When closed it will extend 5 inches above the roof and when open it will extend 9-5/16 inches above the roof. You can use these dimensions to determine if you have the necessary clearance between where you are wanting to install the fan and where your skylight is located.
I have attached an installation video that you might also find helpful.
Product Page this Question was Asked From
MaxxFan Deluxe Roof Vent w/ 12V Fan, Thermostat, and Remote - Powered Lift - 10 Speed - Smoke
- RV Vents and Fans
- Vent
- Roof Vent
- Powered Lift
- 5 Inch
- 12V Fan
- Reversible Fan
- 14W x 14L Inch
- Plastic
- Tinted
- MAXXAIR
more information >
Featured Help Information
Instructions
Miscellaneous Media
Continue Researching
- Shop: Dexter Trailer Axle Beam with E-Z Lube Spindles - 95" Long - 5,200 lbs
- Shop: Grease Seal - Double Lip - 2.125" ID - 3.376" OD - GS-2125DL
- Shop: CE Smith U-Bolt Kit for Mounting 5.2K to 7K, Round Trailer Axles - 7" Long U-Bolts - Zinc
- Shop: U-Bolt Kit for Mounting 5,200-lb to 7,000-lb, Round Trailer Axles - 7" Long U-Bolts
- Q&A: What is the Difference Between 1.25 Inch Trailer Bearings
- Shop: Easy Grease Trailer Hub and Drum Assembly for 5.2K & 6K Axles - 12" - 6 on 5-1/2 - Pre-Greased
- Shop: 10-10 Grease or Oil Double-Lip Seals - Qty 2
- Shop: Grease Seal - Double Lip - 2.250" ID - 3.376" OD - GS-2250DL
- Q&A: Low Profile Roof Vent Recommendation for Camper
- Search Results: fantastic vent
- Q&A: Replacement Roof Flange Assembly For A MaxxAir MaxxFan Deluxe On A 2013 Jayco Eagle Fifth Wheel
- Shop: Trailer Wiring
- Article: Best RV Roof Vents
- Q&A: Weight Distribution Recommendation for a 2024 Jayco Flight 284BHS
- Q&A: Will a MaxxAir MaxxFann Deluxe Roof Vent Mount In Place Of a Fantastic Roof Vent?
- Q&A: Recommended AC With Heat Strip for Enclosed Trailer
- Q&A: Replacement AC Unit for 15k BTU Unit on RV
- Article: How Many Batteries Do You Need to Run RV Air Conditioner?
- Article: 2023 Holiday Must Haves
- Article: Trailer Wiring Diagrams
- Article: Brake Controller 7- and 4-Way Installation Kit (ETBC7)
- Article: Trailer Tire Sizing
- Article: Most Popular Wheel Bearings
Matt R.
5/28/2020
I have plenty of space for the flange, as my solar panels are elevated off the roof on a roof rack. My concern is that widthwise, I have a gap of 18 1/4" between two panels for the actual vent that is mounted above the roof to fit as it opens and closes. Is that enough clearance? If you subtract 16 1/2 from 18 1/4 and then divide it by two you get .875 or 7/8 inch clearance on each side. Font and back, with the 22-1/2 inches length of the fan I have plenty of space. It is just that width I am worried about. Do you know if this will work? Thanks for your time.