Why The Axles Cannot Be Rotated and Original Spring Seats Be Reused When Flipping Trailer Axles
Question:
I was reading about the axle flip, which I am also looking into. I am trying to understand why the spring seats must stay on the bottom of the axle and new seats must be installed. Can you explain why we cannot just rotate the axle so the spring seats are on the top? I have everything apart, as I am replacing the springs and hubs, and it seems to me that I can just rotate the axle so the spring seats are on the top and tighten down the U-bolts in the opposite direction as well??? Thanks
asked by: Dennis
Expert Reply:
The reason you will not want to rotate the axle and just reuse the spring seat is because there is a bow to the axles that flattens out as the weight of the trailer is applied to the axle that if you rotated the axle, the bow would flip and the alignment of the trailer tires would be way off and you would encounter problems with how the tires wear and with overall trailer handling.
This is why the Dexter Trailer Springs Over-Under Conversion Kit # K71-385-00 that you referenced includes an additional set of spring seats for you to bolt onto the axles.
When lifting your trailer you need to keep in mind that the geometry of the trailer will change. You may encounter lower or heavier tongue weight, and/or the trailer may become top heavy, contributing to trailer sway and instability, especially when passing large trucks or in high winds. In these situations, it may require you to go with a weight distribution system with sway control, if you are not already using one. I have provided an faq link and a link to weight distributions systems for you to review.
I attached a picture of how the axles should look once flipped for you to check out.
Product Page this Question was Asked From
Dexter Trailer Springs Over-Under Conversion Kit
- Trailer Suspension Parts
- Alignment and Lift Kits
- Boat Trailer
- Camper
- Car Hauler
- Snowmobile Trailer
- Utility Trailer
- Double Eye Springs
- Round Axle - 3 Inch
- Dexter
more information >
Featured Help Information
Instructions
Miscellaneous Media
Continue Researching
- Shop: Trailer Axle with Idler Hubs - 5 on 4-1/2 Bolt Pattern - 60" Long - 2,000 lbs
- Shop: #84 Spindle for 3,500-lb Trailer Axles - 2" Diameter
- Shop: Trailer Axle w/ Electric Brakes - Easy Grease - 6 on 5-1/2 Bolt Pattern - 95" Long - 5,200 lbs
- Shop: Suspension Enhancement
- Shop: Dexter Trailer Springs Over-Under Conversion Kit
- Shop: RoadActive Suspension Custom Leaf Spring Enhancement Kit
- Shop: RoadActive Suspension Custom Leaf Spring Enhancement Kit - Heavy Duty
- Shop: RoadActive Suspension Custom Leaf Spring Enhancement Kit - Heavy Duty
- Q&A: Best Way to Lift Jayco Eagle
- Search Results: 4 lug axle
- Search Results: over under kit
- Q&A: Should I Use Leaf Spring Spacers Lift Blocks on a Trailer to Raise It
- Search Results: lift blocks
- Shop: Trailer Wiring
- Search Results: tongue bracket
- Article: How to Raise Your Travel Trailer Height
- Video: Review of Lippert Replacement Lift Kit Equalizer Plate - LC84PJ
- Search Results: spring mounting hardware
- Q&A: Recessed Floor Storage Box Compatible with Toyhauler Trailer
- Search Results: 5200 drop axle
- Q&A: How to Measure the Angle of Trailer A Frame To Determine if a 50 Degree A Frame Coupler will Fit
- Q&A: What Is The Angle For The etrailer A-Frame Trailer Coupler?
- Q&A: How Much Will the Dexter Trailer Springs Over-Under Conversion Kit, # K71-385-00 Raise the Trailer
- Q&A: Recommended Tire Storage Covers for 215/75-17.5 Tire Size
- Search Results: underslung
- Video: Fifth Wheel and Gooseneck Wiring Harness Installation - 2004 Ford F-250
- Video: Trailer Hitch Installation - 2007 Ford F-250 - Curt
- Shop: Gooseneck Hitch
- Video: Gooseneck Trailer Hitch Installation - 2007 Ford F-250 Super Duty
- Video: Review of Kenda Trailer Tires and Wheels - Off Road Tire with Wheel - KE78JR
Dan
4/30/2024
I have a dual axle trailer which looks just like the OEM setup, with springs on bottom of axle. I'd like to raise my trailer but am interested in flipping just ONE axle, not both. (Clearance for a dump conversion) Seems this would raise the trailer by about 2 inches instead of 4. The equalizer in middle would not ride level, but seems it should have plenty of articulation. Any reason this wouldn't work? Thank you!