Recommended Trailer Hitch Receiver for 2007 Ford Ranger with Step Bumper
Question:
I have 2007 3.0 ford ranger it’s not a 4x4. I’m towing a Rockwood freedom pop up camper Ltd 1940. Label on camper says. GVWR/2,381 UVW/1,656 does not have generator. CCC/611 lbs. manual calls for class 2. Will your E-S3 work or do I need part 13138?? My truck has a step bumper with a 2” ball I towed it on the bumper ball about 15 miles. Seemed ok. Lol Thanks
asked by: Joey C
Expert Reply:
The Curt 2" Trailer Hitch - Bumper Mount - 8-3/4" Bolt Pattern - 5,000 lbs GTW # E-3S is not a custom fit hitch but it will work for your application on your 2007 Ford Ranger. Your bumper capacity will remain your towing capacity when using this hitch.
The Curt # 13138 is a much stronger option that attaches to your frame instead of the bumper. It will be a much better option for most towing and for other accessories, so it is my recommendation even though the # E-3S will work for your trailer.
With whatever option you choose, I also recommend the etrailer.com Ball Mount Kit for 2" Hitches # 989900. This will give you ball mount options as well as hitch ball options for other trailers. If you don't already have trailer wiring, then I recommend the Hopkins Plug-In Simple Vehicle Wiring Harness with 4-Pole Flat Trailer Connector # HM40655. This harness plugs into your facotyr wiring harness located behind your tail lights.
Products Referenced in This Question
Curt Trailer Hitch Receiver - Custom Fit - Class III - 2"
- Trailer Hitch
- Custom Fit Hitch
- Class III
- 400 lbs TW
- 4000 lbs GTW
- 6000 lbs WD GTW
- 2 Inch Hitch
- 600 lbs WD TW
- Visible Cross Tube
- CURT
more information >
etrailer Ball Mount Kit for 2" Hitches - 7,500 lbs
- Trailer Hitch Ball Mount
- Fixed Ball Mount
- 1-7/8 Inch Ball
- 2 Inch Ball
- Two Balls
- Steel Ball
- Steel Shank - Gloss Black
- Drop - 2 Inch
- Drop - 4 Inch
- Rise - 1 Inch
- Rise - 3 Inch
- Fits 2 Inch Hitch
- 7500 lbs GTW
- Class III
- Ball Mount Kit
- etrailer
more information >
Hopkins Plug-In Simple Vehicle Wiring Harness with 4-Pole Flat Trailer Connector
- Custom Fit Vehicle Wiring
- Trailer Hitch Wiring
- No Converter
- Custom Fit
- 4 Flat
- Hopkins
more information >
Product Page this Question was Asked From
Curt 2" Trailer Hitch - Bumper Mount - 8-3/4" Bolt Pattern - 5,000 lbs GTW
- Bumper Hitch
- 500 lbs TW
- 5000 lbs GTW
- 2 Inch Hitch
- Bolt-On
- CURT
more information >
Featured Help Information
Instructions
Miscellaneous Media
Continue Researching
- Q&A: Slipper Spring Hanger Positioning for 7,000 lb Tandem Axle
- Article: How to Measure for Trailer Hitch Drop
- Q&A: Recommendation For Increasing Strength of Rear Bumper Attached to Spacers Off Of Trailer Frame
- Q&A: Trailer Hitch Receiver Options For A Box Trailer Frame
- Q&A: Recommended Roof Rack for a Interstate 7X16 Cargo Trailer
- Q&A: Replacement Trailer Tires Size 7.50-16LT Load Range F
- Q&A: Trailer Hitch Receiver Fit For 2024 Nissan Pathfinder
- Q&A: How Tall is the Exterior Portion of the Ventline Vanair 12-Volt Trailer Roof Vent # VP-543SP
- Article: My Trailer Hitch Doesn't Fit
- Article: Best Hitches for Travel Trailers (2022) - For a Smooth, Sway-Free Ride
- Article: How to Choose the Right Trailer Hitch Class
- Article: Brake Controller Installation: Starting from Scratch
- Article: Types of Bumpers
- Article: Which Hitches are Made in the USA