Dimensions of the Replacement Silicone Dust Boot w/ Stainless Steel Core Part # K225BSSI

Question

Question:

what are the dimensions of this cover.i need to know for my brakes

asked by: John

0

Expert Reply:

I called my contact at Kodiak and they informed me that the Replacement Silicone Dust Boot w/ Stainless Steel Core part # K225BSSI has an inner diameter (ID) of 1.70" and an outer diameter of 2.77". I have attached a photo of these measurements for you as well.

expert reply by: Conner L

0

click to enlarge

Answer 1

You would want the EZ Lube Drive in Plug with Cap part #RG04-040. This has been confirmed as a fit for trailer hubs that have a hub bore of 1.980 inch.

view full answer...

Answer 2

I do have an option for you but we don't offer any replacement brake pads for the Tie Down Engineering (TDE) 46304 Caliper as the company is no longer in business. Therefore, our only option to you would be a full replacement for which I…

view full answer...

Answer 3

While there is not a manual or video available for the Kodiak Disc Brake Caliper Rebuild Kit #KDBC225KIT I did find an expanded drawing of the parts of Kodiak Disc Brake Caliper #KDBC225S which should help so you can see how the pieces fit. The…

view full answer...

Answer 4

I wasn't able to find any confirmation that the dust boot and seal included in the Kodiak Disc Brake Caliper Rebuild Kit #KDBC225KIT were a compatible fit for a Tie Down 46304 caliper, but I did measure them so that if you wanted to check the…

view full answer...

Answer 5

The side of the Silicone Dust Boot #K225BSSI, that comes with the Rebuild Kit #KDBC225KIT, with the design on the outside ring needs to face in towards the piston while the other side should face the brake pad. I have attached a photo to demonstrate…

view full answer...

Answer 6

From the numbers you provided it sounds like you need replacement grease seals. In my research, the grease seals I found with the GS-1719DL number have a 1.72 inside diameter and 2.565 outside diameter. The replacement double lip grease seals you…

view full answer...

Answer 7

I wish we had an install video or even a manual for the Kodiak Caliper Rebuild kit #KDBC225KIT that you referenced but the best we can offer at this time is an exploded diagram that shows how all of the parts go together.

view full answer...

Answer 8

The caliper bracket you are looking for is the Replacement Mounting Bracket #KCMB12D which is compatible with the 5 bolt mounting flange you have as well as the 225 Kodiak Dacromet calipers you have as well. Then for a bolt kit you'd want the…

view full answer...

Answer 9

If your current springs have 5 leaves then going to a 7 leaf spring will increase the height of the trailer a little and make the trailer more susceptible to sway. Regarding capacity if you go with springs rated higher than what is required it will…

view full answer...

Answer 10

Since Demco uses 3,500 drum brake assemblies part #DMSB24429M and #DMSB24428M what you'd need is similar 3,500 electric brake assemblies like the etrailer part #AKEBRK-35L-SA for the left hand side and #AKEBRK-35R-SA for the right hand side. To…

view full answer...

Answer 11

If your old axles have a 5 bolt brake flange the assemblies like Dexter Electric Trailer Brake Assembly - 12" - Left Hand - 6,000 lbs part #23-105 or Dexter Electric Trailer Brake Assembly - 12" - Right Hand - 6,000 lbs part #23-106 will…

view full answer...

Answer 12

The 40 amp fuse for your 2006 Chevrolet Silverado tow package is used for the 12 volt battery charge circuit. This fuse is located toward the front of the underhood fuse box closest to the front auxiliary positive post (see photo). There may be a…

view full answer...

Dimensions of the Replacement Silicone Dust Boot w/ Stainless Steel Core Part # K225BSSI

Continue Researching