Lippert Ground Control Leveling System 3.0 Bad Zero Point
Question:
The touch pad shows a Bad Caliberation code on the display and we can not turn the unit off to reset zero point.
asked by: Bob D
Expert Reply:
If you are receiving the ****ERROR**** "Auto Level Fail" LCD Message on for your Lippert Ground Control 3.0 # LC358590 then that means it is either unable to auto level because of uneven ground or it is unable to auto level because the "Zero Point" has been set incorrectly.
If it is due to uneven ground then you will want to move your RV to a new location that is a little more level.
If it is due to to the Zero Point not being set correctly then you can follow the Zero Point Calibration steps which can be found in your copy of the owner's manual:
Zero Point Calibration
The “Zero Point” is the programmed point that the trailer will return
to each time the Auto Level feature is used.
Note: Prior to starting this procedure, double check all connections
on the controller, jacks, and touch pad.
1. In manual mode, run the jacks to level the trailer. This is best
achieved by placing a level in the center of the trailer and leveling
it both front to back and then side to side. (See “Basic Jack
Operation” for instructions on how to manually operate the system).
2. Once the trailer is level, turn off the touch pad.
3. With the touch pad off, press and release the “FRONT” button five (5) times and then press and release the “REAR” button five (5) times.
4. The touch pad will flash and beep and the display will read “ZERO
POINT CALIBRATION ENTER to set, Power to Exit”.
5. To set the current position as the zero point, press the “ENTER”
button.
6. LCD display will read “Zero point stability check”.
7. LCD display will read “Zero point set successfully” once process is
complete.
8. The system will set this point as its level state and the touch pad
will turn off.
If you have a different error code just let me know and I can look into it for you.
Product Page this Question was Asked From
Lippert Ground Control 3.0 Electric 5th Wheel RV Leveling System w Touchpad - 4-Point Set
- Camper Jacks
- Fifth Wheel Camper
- Leveling Jacks
- Stabilizer Jacks
- Steel
- 10001 lbs or More
- Electric Jack
- 36 Inch Lift
- Bolt-On
- 4 Jacks
- Lippert
more information >
Featured Help Information
Instructions
Continue Researching
- Q&A: How to Reset Zero Point Calibration on Lippert Ground Control 3.0
- Shop: Replacement Touchscreen Remote w/ Charger for Lippert Ground Control 3.0 Electric Leveling System
- Q&A: Is The Pad For The Replacement 22-1/2" Legs For The Ground Control 3.0 Welded Or Pinned In Place
- Q&A: Wiring Diagram for 5th Wheel Trailer Landing Gear with Red, Black, White, and Green Wires
- Q&A: Wiring Guide for Installing 5th Wheel Landing Gear Motor Switch
- Q&A: Which Lippert Ground Control 3.0 System Is Recommended for a 37' Fifth Wheel
- Q&A: Can I Install a 4-Point Control Module to a 6-Point Lippert Ground Control and Only Use Four Jacks?
- Q&A: Drawing Schematic of Replacement I-Beam Jack Bracket for Lippert Ground Control 3.0
- Article: How to Raise Your Travel Trailer Height
- Article: 4 Steps to Choosing Your 5th Wheel Pin Box
- Article: Trailer Wiring Diagrams
- Article: How to Level Your Fifth Wheel in 3 Simple Steps (Manual or Auto-Level)
- Article: Gooseneck to 5th Wheel Adapters
- Article: Brake Controller 7- and 4-Way Installation Kit (ETBC7)
- Article: Double-Eye Trailer Suspension System Review