Air Line Compatibility with Air Lift Union T-Piece for 1/4-Inch Air Lines AL21838

Question

Question:

will this work with Firestone air tubing?

asked by: Travis

0

Expert Reply:

Yes, the Air Lift Union T-Piece for 1/4-Inch Air Lines # AL21838 will work with standard 1/4-inch air line tubing on any brand of air bag suspension kit whether it is AirLift, Firestone or another brand. All such systems use the same air tubing, like # AL22007.

expert reply by: Adam R

0

Answer 1

The Air Lift LoadLifter 5000 Ultimate Plus kits like the part #AL88288 that come with the braided lines actually also come with the nylon air tubing that runs to the inflation valve still which would be where you'd install a union tee like the…

view full answer...

Answer 2

We carry union tees for 1/4" diameter tubing with part #AL21838 and union tees for 3/8" diameter tubing with part #F3105-1. Both of these tees require you to cut into the tubing and push them in to the fittings on the tee to seal them…

view full answer...

Answer 3

All you need to do that is the union tee part #AL21838 to pull that off. You'd run the air line from both bags to it and then the inflation line from the valve stem to the center tee and you'd be set. For nearly all people this is the easier…

view full answer...

Answer 4

The Air Lift Union T-Piece #AL21838 referenced in your question is designed for 1/4 inch diameter air lines like what Air Lift uses for their suspension systems. This T-Piece can be used to fit two air bags together.

view full answer...

Answer 5

To release an air line from one of the T-Pieces #AL21838 that came with your Air Lift Load Controller Compressor System #AL25856 you just need to put even pressure on the circular piece that the hose slides into. If you check out the attached video…

view full answer...

Answer 6

Hey Scott, congrats on your new 2020 Nissan Titan SV 2WD! I definitely recommending installing the Air Lift LoadLifter 5000 Air Helper Springs #AL57331 instead of an RAS kit just because you get more adjustability out of the air bags. They do require…

view full answer...

Answer 7

It sounds like the purpose of getting the air helper spring would be to counteract the 1 inch compression you're getting in your rear suspension caused by the pin weight of your 5th wheel. If that's the case, I believe that the AirLift 5000…

view full answer...

Answer 8

For sag from towing a trailer the best recommendation I can make is actually a weight distribution system. Suspension enhancement will help level your truck while towing. But the advantage to a weight distribution system is that it levels the vehicle…

view full answer...

Answer 9

Hey Tarek, for your 2023 Ford Raptor I recommend checking out the Timbren Suspension Enhancement System #T75MR. This suspension enhancement system has a load leveling capacity of 3,000 lbs, will increase stability while reducing sag, and will install…

view full answer...

Answer 10

Since the pin weight of your camper is 2.1k, I recommend going with the LoadLifter 5000 opposed to the 7500. While technically there is not reason you couldn't use the 7500 kit, it really is not necessary for a camper like yours. Generally the…

view full answer...

Answer 11

The Air Lift LoadLifter 7500 XL Air Helper Springs #AL57531 will fit your 2022 Ram 3500 Mega Cab with single rear wheels. This is the extra heavy duty 7,500 lb kit so it is most commonly used on dually trucks, but it will fit single rear wheel models…

view full answer...

Answer 12

Installing the Union Tee #AL21838 with your #AL57575 will tie the pressure of the two air bags together. So yes, a shift in a very heavy load like a truck camper will potentially result in air being forced from one into the other. The reason I say…

view full answer...

Air Line Compatibility with Air Lift Union T-Piece for 1/4-Inch Air Lines AL21838

Product Page this Question was Asked From

Continue Researching