Separating Turn Signals from Brake Lights for Third Brake Light on a Camper Shell

Question

Question:

Do you offer a logic box that works with standard incandescent lights? The 3rd brake light is on a pickup truck canopy.

asked by: Eric

0

Expert Reply:

Any basic converter box will separate out turn signals from brake lights but I recommend the vehicle to vehicle converter # 118158. On the input side the white wire is ground, yellow connects to the combined left turn signal/brake light wire on the vehicle, and green connects to the right turn signal/brake light wire. These all have to be connected for the box to work.

On the output side the red wire will be brake lights only. Green and yellow are turn signals only but can be capped off since they would not be needed in this situation.

expert reply by: Michael H

0

Answer 1

You can use 7-way trailer wiring with the module part #PP20-702 to provide power to the third brake light of your camper shell/cap. Basically the stop/turn circuits of the trailer wiring need to run to the yellow wires of this module and then the…

view full answer...

Answer 2

The logic box that you are asking about is our Pacer Performance 3rd Brake Light Logic Module #PP20-702. This is a piece of equipment that is required when using an LED light as a 3rd brake light. If there is a specific light style that you are…

view full answer...

Answer 3

The Pacer Performance 3rd Brake Light Logic Module part #PP20-702 is your best option to isolate the brake signal from the turn signal for a third brake light. However, the issue that you are experiencing is that some LEDs simply don't draw…

view full answer...

Answer 4

To wire in the 3rd brake light from the camper shell to your 2019 Chevy truck I recommend using the Pacer 3rd Brake Light Module #PP20-702. This is designed specifically for single LEDs and will filter out the turn signal input so that it doesn't…

view full answer...

Answer 5

Yes, you can connect a 3rd Brake Light Logic Module #PP20-702 to a 4-Way Flat Trailer Connector #HM48110. This will filter our the turn signals from the brake lights on your trailer connector. Then you will only need to run the power and ground wire…

view full answer...

Answer 6

In order to wire this up the way you want, and also be able to disconnect it easily, I suggest using the Hopkins 4-Pole Flat Wiring Extension - 120" Long #HM48235 and the 3rd Brake Light Logic Module #PP20-702. I would start by cutting the…

view full answer...

Answer 7

If you absolutely do not want to splice into the vehicle you could use the trailer connector to power the third brake light on a truck bed camper but the issue with using the trailer connector is that the stop/turn circuits are combined. Therefore,…

view full answer...

Answer 8

Yes we do have a logic module that will work to wire your third brake light on your camper shell, part #PP20-702 the Pacer Performance 3rd Brake Light Logic Module. The third brake light needs to have a brake signal only, and if you are tapping into…

view full answer...

Answer 9

There is a simple solution to get the isolated brake signal from your combined turn signal and brake wiring. You will simply use the Pacer Performance 3rd Brake Light Logic Module #PP20-702. The module filters out the unwanted turn signal. This will…

view full answer...

Answer 10

Do you have any specific questions that you need help with? The process for installing the interior light will be pretty straight forward. There will be a 12 volt power wire you need to run to the battery with a fuse/circuit breaker and then a ground…

view full answer...

Answer 11

For your 2021 Chevrolet Silverado you will have to splice into the factory wiring to use the 3rd Brake Light Logic Module #PP20-702 to connect the left and right turn signals, along with the green wire. You can also combine this harness #PP20-702…

view full answer...

Answer 12

The T-One Vehicle Wiring Harness with 4-Pole Flat Trailer Connector part #118416 is a fit for a 2015 Jeep Wrangler. If you would like to use this to wire in a some type of third brake light then you can do so just note that the stop and turn signals…

view full answer...

Separating Turn Signals from Brake Lights for Third Brake Light on a Camper Shell

Products Referenced in This Question

Product Page this Question was Asked From

Featured Help Information

Instructions

Miscellaneous Media

Continue Researching