Should Axles be Aligned with the Tongue or Frame on Trailer with Tongue that was Welded Off-Center
Question:
I have changed my single axle pontoon trailer to a tandem axle trailer. I fabricated two indentical slides from 1/4 inch by 2-1/2 inch angle iron which have the spring hangers and fender mounts welded to them. These are then clamped to the trailer frame tubing. When trying to align the axles, I discovered the tongue of this factory built tracker trailstar trailer is offset by about 1/2 to 3/4 of an inch to the right of the trailer center. It is not bent, it was welded up this way from the factory. Should I align my axles to the hitch, which causes them to sit at a slight angle on the frame, or align them so they are square to the frame?
asked by: Mark M
Expert Reply:
When aligning the axles on your Trailstar Trailer, I recommend aligning them so that they are square to the trailer's frame. Doing this will maintain the load capacity and structural integrity of the trailer itself. If you were to instead align the trailer to the tongue, it would shift the load bearing components of the trailer off-center, essentially reducing it to an unknown capacity. This may have an effect on other components as well, such as the suspension and wheels.
The only drawback I can think of with having the axles offset from the trailer tongue, is that at some point down the line you may experience some uneven tire wear. This is simply because the trailer is going to be constantly trying to pull itself to center behind your tow vehicle. With that being said, a 1/2 to 3/4 of an inch offset should not cause too much of an issue.
Product Page this Question was Asked From
Curved Equalizer for 1-3/4" Wide Double-Eye Springs - 7-3/4" Long - 9/16" Center Hole
- Trailer Suspension Parts
- Standard Equalizer
- Camper
- Car Hauler
- Utility Trailer
- Double Eye Springs
- 7-3/4 Inch Long
- Tandem Axle
- Triple Axle
- etrailer
more information >
Continue Researching
- Search Results: hangers trailer leaf spring suspension
- Video: Optronics Trailer Lights - Tail Lights - TLL9RK Review
- Video: Easy Swivel Trailer Jack Installation
- Video: Dutton-Lainson Trailer Jack - Side Frame Mount Jack - DL22800 Review
- Video: Review of Dexter Trailer Leaf Spring Suspension - Hangers - DX54CR
- Shop: Rear Hanger with Bushing for Single Axle Trailer Suspensions with 1-3/4" Double Eye Springs
- Search Results: trailer bump stop
- Search Results: trailer light kit
- Search Results: trailer wiring harness
- Search Results: chain connectors
- Search Results: chain mount
- Search Results: weld on chain
- Shop: etrailer Boat Trailer Jack w/ Wheel - Sidewind - Swivel - 10" Lift - Zinc - 1,000 lbs
- Shop: LED Combination Tail Light Kit for Trailers under 80" Wide - Submersible - Driver and Passenger
- Shop: Combination LED Trailer Tail Light - Submersible - 6 Function - 11 Diodes - Passenger Side
- Shop: Submersible, Under 80" Trailer Light Kit with 25' Wiring Harness
- Shop: Wesbar 4-Way Flat Trailer Wiring Harness - 20' Long
- Shop: Pull Pin, Easy Swivel Trailer Jack with 8" Wheel - Sidewind - 1,500 lbs. by Dutton-Lainson
- Video: Erickson Spare Tire Carrier - Frame Mount - EM77316 Review
- Video: CargoSmart Spare Tire Carrier - E-Track Mount - 3481743 Review
- Q&A: Can Lock Nuts Be Reused on Trailer Suspension Bolts After Being Removed
- Q&A: How Does the Rear Hanger Get Welded to the Trailer Frame
- Q&A: What are the Proper Components Needed to Install the Leaf springs On a Trailer
- Q&A: How To Mount Redline Rear Hanger # 30-20 On A Trailer
- Q&A: Hanger Spacing Needed for Single Axle Trailer with 25-1/4 inch Long Leaf Springs
- Q&A: How To Determine If Timbren Trailer Suspension Enhancement # TTRA1702 Will Fit Single Axle Trailer
- Video: Dexter Axle Trailer Hubs and Drums - Hub - 8-258-50UC1-EZ Review
- Q&A: What is Minimum Trailer Axle to Frame Clearance for Leaf Spring Deflection