How to Pick Out Landing Gear Jacks for 1996 Coachmen Catalina
Question:
landing gear for 1996 coachmen catalina
asked by: Thomas B
Expert Reply:
In order to pick out a direct replacement for the landing gear on your 1996 Coachmen Catalina we would need to know the distance between the mounting brackets. Otherwise you could just have the brackets removed from your trailer by a qualified welder and then install the brackets that come with the Bulldog Tandem Landing Gear Set # BD500162. Either way this landing gear set would work well for you, you just might have to have the brackets of your trailer removed and then install the brackets of the # BD500162.
I attached a picture that shows the dimensions that this landing gear set would fit with.
The jacks would be the correct replacement for Lippert, Venture, and Atwood landing gear, as well as those from a few other manufacturers. The sure way to tell is that if the distance between the mounting brackets (underside of top bracket to top of lower bracket as shown in the diagram) is 17-1/2 inches. If this is the case, the landing gear should fit just fine.
If your frame clamps are instead 20-1/4 inches the Ultra Fab part # UF17-943010 would be a direct replacement.
Products Referenced in This Question
Bulldog Tandem Landing Gear Set - Drop Leg - 36" Lift - 8,000 lbs
- Camper Jacks
- Fifth Wheel Camper
- Leveling Jacks
- Stabilizer Jacks
- Steel
- 7001 - 8000 lbs
- Landing Gear
- Sidewind Jack
- 36 Inch Lift
- Bolt-On
- 2 Jacks
- Bulldog
more information >
Ultra-Fab Deluxe Electric Landing Gear Set - 38" Lift - 12,000 lbs
- Camper Jacks
- Fifth Wheel Camper
- Leveling Jacks
- Stabilizer Jacks
- Steel
- 10001 lbs or More
- Electric Jack
- Landing Gear
- 38 Inch Lift
- Weld-On
- 2 Jacks
- Ultra-Fab Products
more information >
Product Page this Question was Asked From
Stromberg Carlson Electric Landing Gear Set - Weld On - 34-7/8" Lift - 5,500 lbs
- Camper Jacks
- Fifth Wheel Camper
- Leveling Jacks
- Stabilizer Jacks
- Steel
- 5001 - 6000 lbs
- Electric Jack
- Landing Gear
- 35 Inch Lift
- Weld-On
- 2 Jacks
- Stromberg Carlson
more information >
Featured Help Information
Instructions
Continue Researching
- Q&A: Replacement Landing Gear for 2002 Carriage Cameo F34CK3 5th Wheel Trailer
- Q&A: Landing Gear Recommendation for a 2002 Carriage Cameo Fifth Wheel Model F34CK3
- Q&A: Replacement Landing Gear for a Keystone Laredo 5th Wheel Trailer
- Q&A: Troubleshooting Landing Gear on Fuzion Toy Hauler That Will No Longer Lift Trailer
- Q&A: Replacement Powered Landing Gear Setup for 2007 Keystone Laredo LA25RK07
- Q&A: Complete AC System With An Advent 13.5K BTU Low Profile AC Unit
- Q&A: Reese and B and W Fifth Wheel Hitch Solutions that Fit 2013 Chevy Silverado Short Bed 2500 Denali
- Article: Trailer Wiring Diagrams
- Article: Performance Chips and Modules
- Article: Wiring Trailer Lights with a 7-Way Plug (It's Easier Than You Think)
- Article: Stability Control for Heavy Duty Vehicles
- Article: What is Boondocking
- Article: Rooftop Cargo Carriers
- Article: How to Measure for Travel Trailer and Fifth Wheel Steps