EZ Loader Trailer Replacement Snap-Ring Swivel Trailer Jack
Question:
I want to replace my trailer jack. I’m having a hard time choosing which size fits my trailer. I have an EZ leader trailer that came with my 1999 Yamaha Exciter 270 jet boat. The jack swivel plate is welded on the trailer and it uses a snap ring to hold the jack in place. Can you guys help me out? Thanks
asked by: Chris
Expert Reply:
From my research, EZ loader trailers used a Fulton jack with a swivel snap-ring on their aluminum boat trailers. Therefore the correct replacement snap-ring jack for your trailer would be the Fulton Round, Snap-Ring Swivel Marine Jack part # FTJ120W0301.
As long as the snap ring pilot hole on your trailer's jack mount is 2.3" in diameter then this jack will be a direct replacement for you. This jack has a 1,200 lb weight capacity offering up to 23" of lift. Please note that a trailer jack does not need to be rated for the gross trailer weight (GTW), just the tongue weight (TW).
The jack also comes with a weld-on bracket should your pilot hole diameter be different than 2.3". I have attached a review video of this jack for you as well.
Product Page this Question was Asked From
Fulton Round, Snap-Ring Swivel Marine Jack - Weld On - Sidewind - 10" Lift - 1,200 lbs
- Trailer Jack
- Boat Trailer
- Leveling Jacks
- Tongue Jacks
- Steel
- 1001 - 2000 lbs
- Sidewind Jack
- Swivel Jack
- 10 Inch Lift
- Weld-On
- With Wheel
- Fulton
more information >
Continue Researching
- Search Results: fender
- Search Results: trailer jack landing gear
- Search Results: ram
- Search Results: fender for trailer
- Search Results: cable for ramp door
- Search Results: ram jack
- Search Results: bulldog
- Q&A: Recommended Trailer Jack For Trailer With 800 Lbs. Of Tongue Weight
- Shop: Bulldog Winch Standard Series Truck Power Unit Assembly - GenB
- Shop: Americana Trailer Wheel Center Cap - Stainless Steel - 4.88" to 4.90" Pilot
- Shop: Single Axle Trailer Fender for Enclosed Trailer - Ribbed Steel - 15" to 16" Wheels - Qty 1
- Shop: Ultra-Fab Steel Jumbo Roller for Trailers and RVs - Weld On - 2-1/2" Wide x 3" Tall
- Shop: Dexter Trailer Hub and Drum Assembly - 7K lb E-Z Lube Axle - 12" - 8 on 6-1/2 - 1/2" Studs
- Shop: Single Axle Trailer Fender for Enclosed Trailer - Ribbed Steel - 13" to 15" Wheels - Qty 1
- Shop: Bulldog 2-Speed Jack - Drop Leg w/ Spring Return - Traditional - 26" Lift - 10,000 lbs
- Shop: Vehicle Engine Heaters
- Q&A: Replacement Entry Door and Deadbolt Locks for RV
- Q&A: Replacement for Shelby Industries Model 5756 Boat jack
- Q&A: Replacement Idler Hub For Old Boat Trailer With DICO 45264 Idler Hubs
- Q&A: Is There a Replacement for a Shelby Jack 5856A That Uses Existing Bracket
- Article: Trailer Wiring Diagrams
- Q&A: Replacement Trailer Jack Recommendation for Shelby # 5856A
- Q&A: Replacement Jack for Bulldog Model 130 Marine Jack
- Article: Best Boat Trailer Jacks
- Article: Trailer Jacks
- Article: Trailer Maintenance Schedule
- Article: Pintle-Hitches
- Article: Brake Controller 7- and 4-Way Installation Kit (ETBC7)
- Article: Trailer Lighting Requirements