Replacement Wheel Tray for the Thule Big Mouth Roof Mounted Bike Carrier

Question

Question:

Will the 853-7628 wheel tray be used for the 599xt Big mouth upright carrier. The part no. listed on the manual is 853-1402-56

asked by: Dominic D

0

Expert Reply:

The part # 853-7628 that you referenced is the replacement tray for the Thule Prologue XT Roof Bike Rack. What you are looking for is part # 853-5423-56 which is the correct Replacement Wheel Tray for the Thule Big Mouth Roof Mounted Bike Carrier. I called Thule and my contact confirmed that this is the correct replacement part for your carrier.

expert reply by: Jon G

0

Answer 1

Aside from a slight change in the appearance of the crossbar (the WingBar Evo has some boxed edges as opposed to the completely smooth front of the AeroBlade) the biggest differences are the rubber strip on top of the crossbar and the weight…

view full answer...

Answer 2

The Thule Big Mouth, manufactured from 1999-2017 uses #753-3236 as the end cap, which includes the plate that has the Thule name on it. That's the part number you'd want to use, according to Thule. The #853-5424 will also work, but it…

view full answer...

Answer 3

The Thule Big Mount went through a change at one point that included the end caps. The end cap it was changed to was #753-3236. Prior to that it looked more like #853-7629 that you have referenced but it is not the same end cap. Your bike rack wheel…

view full answer...

Answer 4

It's very likely the latter, but it depends on the specific Thule Big Mouth rack you have, as there were two of them, the original Big Mouth Upright 599XT and the Big Mouth 599XTR. It is likely the 599XTR, as they were around far longer. The…

view full answer...

Answer 5

I attached the install instructions for the Thule XADAPT9 part #THXADAPT9 that you referenced which I hope clears up the issue you are experiencing.

view full answer...

Answer 6

The Thule Prologue Roof Mounted Bike Rack that you referenced will work with the Thule Aeroblade crossbars on your 2006 Jeep Grand Cherokee with the XADAPT9 load bar adapter, #THXADAPT9. This adapter comes with a curved metal bracket for the rear…

view full answer...

Answer 7

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 8

Since you have a wheelbase/axle spacing of 38 inches the correct hanger kit for slipper springs would be the part #HAP-105-205-01. And then for a 7k trailer axle the u-bolt kit you'd want would be the part #APUBR-8. I attached the diagram to use…

view full answer...

Answer 9

I've never heard of an actual third brake light connector on a camper shell to plug in on a truck and we don't carry any parts to do that. The light generally needs to be hardwired into the truck's brake light circuit. The issue with this…

view full answer...

Answer 10

What you're going to need is two of the transfer switches in that case. I have attached a diagram from Furrion that shows you how you're going to need to hook the two transfer switches #F30ATS up: -one to the other, then one branching off to…

view full answer...

Answer 11

I would be happy to help you set up your 2022 Toyota Highlander to haul your new travel trailer. The wiring harness you currently have controls your trailer's lighting functions only. You do not need to rewire your Toyota you just need another…

view full answer...

Answer 12

I have a solution for you, but we do not carry Glo-Brite lights, so replacing it with the same brand will not be something I can offer you. Instead, to replace your Glo-Brite 9852-88, I recommend using the Optronics LED Trailer Tail Light #STL72RB.…

view full answer...

Replacement Wheel Tray for the Thule Big Mouth Roof Mounted Bike Carrier

Products Referenced in This Question

Product Page this Question was Asked From

Continue Researching