Brake Controller Recommendation for 2008 Ford Expedition with 4-Way
Question:
OK, so i watched the video on installation on the 2008 Expedition. Which I have. But the video doesnt explain if you have to wire to a round 7 pin connector, which i dont have. Do you have anything that explains that? I would hate to buy your product without knowing how to hook it up.
asked by: David G
Expert Reply:
For your 2008 Ford Expedition you would need a brake controller, the install harness, and a 7-way adapter to install the brake controller.
For a brake controller I would recommend the Prodigy P2 Brake Controller part # 90885. This is our best selling brake controller because of how well it works and how easy it is to setup. This is a proportional brake controller that senses the amount of braking the tow vehicle is applying and applies a proportionate amount to the trailer brakes. This will be the last brake controller you buy. It can easily be transferred to future vehicles as well.
The install harness you need then is the part # 3035-P which plugs in under the dash.
Now with the 37185 there are a few more connections needed to be made at the rear of the vehicle.
Follow the 4-way trailer connector wires from the trailer connector to the front of the vehicle. These wires connect to a factory plug along the frame rail, usually on the driver's side, between the back tires and the rear bumper. The factory plug should be mated to another connector which has wiring that continues back toward the bumper.
There are more wires coming from the front of the vehicle than there are coming out toward the 4-Way plug. Run the blue wire here to the blue wire of the adapter.
Products Referenced in This Question
Adapter 4-Pole to 7-Pole and 4-Pole
- Trailer Wiring
- Wiring Adapters
- Multi-Function Adapter
- 4 Flat
- Plug and Lead
- 4 Flat
- 7 Round - Blade
- Hopkins
more information >
Tekonsha Prodigy P2 Trailer Brake Controller - 1 to 4 Axles - Proportional
- Trailer Brake Controller
- Proportional Controller
- Electric
- Electric over Hydraulic
- Automatic Leveling
- Under-Dash Box
- Dash Mount
- Up to 4 Axles
- LED Display
- Up to 360 Degrees
- Tekonsha
more information >
Product Page this Question was Asked From
Tekonsha Plug-In Wiring Adapter for Electric Brake Controllers - Ford, Lincoln, Mercury
- Accessories and Parts
- Trailer Brake Controller
- Wiring Adapter
- Plugs into Brake Controller
- Vehicle Specific
- Tekonsha
more information >
Featured Help Information
Instructions
Miscellaneous Media
Continue Researching
- Shop: Brake Controller
- Article: Brake Controller Installation on a Ford Full-Size Van
- Article: Trailer Wiring Diagrams
- Article: Brake Controller 7- and 4-Way Installation Kit (ETBC7)
- Article: Wiring Trailer Lights with a 7-Way Plug (It's Easier Than You Think)
- Article: Towing a Trailer? Let's Talk About Brake Controllers
- Q&A: Recommended Replacement Brakes for a 2007 Pace Trailer w/ 15 Inch Rims
- Q&A: Parts Needed To Install a 7-Way and Trailer Brake Controller On a 1996 Ford F-350 With Factory 4-Way
- Q&A: Where is Brake Controller Install Port for 2018 Ford Explorer
- Article: Brake Controller Installation: Starting from Scratch
- Article: Breakaway Kit Installation for Single and Dual Brake Axle Trailers
- Q&A: My Vehicle has a 4-Pin Trailer Plug, but Trailer has 7-Pin Trailer Plug
- Q&A: Best Brake Controller for a 2014 Fleetwood Bounder Motorhome
- Q&A: Location of Brake Controller Wiring Connector on 2014 Fleetwood Bounder on Ford F-53 Chassis
- Q&A: Brake Controller Recommendation for a 2021 Ford F-53 with Brake Controller Harness