Outside Width Dimension of the Redline Trailer Hanger # E4139
Question:
You give the height dimension, and the hole dimension. What is the width dimension doesnt matter if it is in between the horizontal sides, or if it includes that thickness as you have stated it is 3/16 thick. I am trying to figure out if it will fit inside of an existing C channel on the trailer.
asked by: Jeremy
Expert Reply:
I went out into our warehouse and pulled a Front/Center/Rear Hanger for Double-Eye Springs, part # E4139, and measured the outside width of it.
It measures 2-5/16 inches from the outside of one side of the # E4139 to the other side. Check out the picture to the right to see this measurement.
Product Page this Question was Asked From
Front/Center/Rear Hanger for Double-Eye Springs - 4-1/4" Tall - 9/16" Bolt Hole
- Trailer Leaf Spring Suspension
- Hangers
- Boat Trailer
- Camper
- Car Hauler
- Snowmobile Trailer
- Utility Trailer
- Double Eye Springs
- 9/16 Inch Diameter
- 4-1/4 Inch Tall
- Single Axle
- Tandem Axle
- Triple Axle
- Redline
more information >
Continue Researching
- Shop: Front/Center/Rear Hanger for Double-Eye Springs - 4-1/4" Tall - 9/16" Bolt Hole
- Q&A: What is Bolt Hole Diameter for Suspension Hanger # E4139
- Video: Review of Dexter Trailer Leaf Spring Suspension - Shackle Bolts - 007-003-01
- Shop: MORryde X-Factor Crossmember for Standard Frame Hangers
- Video: Redline Trailer Suspension - Leaf Spring Suspension - E4139 Review
- Q&A: Bolt Grade of Hardware that Comes with the Suspension Kit for Tandem-Axle Trailers AP233
- Shop: MORryde Suspension Upgrade Kit for Tandem Axle Trailers - 3-1/8" Long Shackle Straps
- Video: Redline Trailer Suspension - Leaf Spring Suspension - 115919 Review
- Shop: Center Hanger for Double-Eye Springs - 5-7/16" Tall - 3/4" Bolt Hole
- Search Results: cre3000
- Shop: Front/Center/Rear Hanger for Double-Eye Springs - 3-1/4" Tall - 9/16" Bolt Hole
- Shop: Dexter Heavy-Duty Suspension Kit for Tandem-Axle Trailers - 1-3/4" Wide Double Eye Springs
- Q&A: MORryde CRE3000 Equalizers, X-Factor Cross Members & SumoSprings For 2020 Keystone Outback 291UBH
- Shop: Rear Hanger for 2" Wide Slipper Springs - 5-1/4" Tall - 5/16" Bolt Hole
- Search Results: 115918
- Search Results: hanger
- Article: 5 Tell-Tale Signs It’s Time to Replace Your Trailer’s Leaf Springs
- Search Results: spring hanger
- Search Results: x factor
- Search Results: x~factor
- Video: MORryde Standard Frame Hanger X-Factor Crossmember Installation - 2014 Jayco Pinnacle Fifth Wheel
- Video: MORryde LRE RE, or TRE Leaf Spring Suspension X-Factor Crossmember Review
- Video: Review of MORryde X-Factor Crossmember For Standard Frame Hangers - MR33WR
- Video: MORryde Standard Frame Hanger X-Factor Crossmember Review
- Q&A: Upgrading To MORryde CRE3000 Rubber Equalizers On a 2003 Fleetwood Wilderness 5TH Wheel Camper
- Q&A: How To Measure Leaf Springs on a 2015 Grand Design Reflection 308BHTS For Additional Stability
- Q&A: How To Install MORryde X-Factor Crossmember With Leaf Spring Hangers Wider Than 3
- Q&A: Are MORryde X-Factor Crossmembers Available Separately?
- Search Results: leaf spring hangers
- Shop: Suspension Enhancement