Will Curt Bumper Hitch E-3S Fit a 2007 Dodge Ram 1500
Question:
will hitch fit 2007 dodge ram 1500
asked by: charlie
Expert Reply:
The Curt # E-3S bumper hitch is a universal application, so it does not have vehicle specific fits. This hitch would mount using four holes, two that would use 3/4 inch diameter bolts, and two that use 1/2 inch diameter bolts.
You will need to measure to determine if the # E-3S hitch will work on your 2007 Dodge Ram 1500. The 3/4 inch holes are 8-3/4 inches apart, from center to center, and the 1/2 inch holes are 6-1/6 inches apart from center to center. These holes would need to be drilled if not present.
You would also have the option of installing a custom-fit hitch like part # C15409, which is rated to tow up to 17,000lbs.
To wire your truck for towing, you would use hardwire kit # 119178KIT if it did not come with a factory tow package. Models with the tow package would use wiring harness # 118381.
You would also need a ball mount, hitch pin or lock, and a hitch ball to complete your towing setup. The recommended ball mount would be part # 80232, which would put the hitch ball at the most common trailer height. This ballmount can be secured to the hitch using a basic hitch pin like part # PC3, or a hitch lock like part # 7683.
An interchangeable ball like part # 901B would set you up for towing trailers that use either a 2 inch or 1-7/8 inch diameter hitch ball.
Products Referenced in This Question
T-One Vehicle Wiring Harness with 4-Pole Flat Trailer Connector
- Custom Fit Vehicle Wiring
- Trailer Hitch Wiring
- No Converter
- Custom Fit
- 4 Flat
- Tekonsha
more information >
Tekonsha Tail Light Converter with 4-Way Flat Trailer Connector and Install Kit
- Custom Fit Vehicle Wiring
- Trailer Hitch Wiring
- Converter
- 1-1/2 Feet Long
- Universal Fit
- 4 Flat
- Tekonsha
more information >
Curt Trailer Hitch Receiver - Custom Fit - Class V XD - 2"
- Trailer Hitch
- Custom Fit Hitch
- Class V
- 2550 lbs TW
- 17000 lbs GTW
- 17000 lbs WD GTW
- 2 Inch Hitch
- 2550 lbs WD TW
- Visible Cross Tube
- CURT
more information >
Product Page this Question was Asked From
Curt 2" Trailer Hitch - Bumper Mount - 8-3/4" Bolt Pattern - 5,000 lbs GTW
- Bumper Hitch
- 500 lbs TW
- 5000 lbs GTW
- 2 Inch Hitch
- Bolt-On
- CURT
more information >
Featured Help Information
Instructions
Miscellaneous Media
Continue Researching
- Q&A: Slipper Spring Hanger Positioning for 7,000 lb Tandem Axle
- Q&A: Trailer Hitch Receiver Options For A Box Trailer Frame
- Q&A: Will Honda Generator Fit In DeeZee Trailer Tongue Toolbox
- Q&A: Recommended Roof Rack for a Interstate 7X16 Cargo Trailer
- Q&A: Replacement Trailer Tires Size 7.50-16LT Load Range F
- Q&A: Trailer Hitch Receiver Fit For 2024 Nissan Pathfinder
- Article: How to Measure for Trailer Hitch Drop
- Article: My Trailer Hitch Doesn't Fit
- Q&A: How Tall is the Exterior Portion of the Ventline Vanair 12-Volt Trailer Roof Vent # VP-543SP
- Article: Best Hitches for Travel Trailers (2022) - For a Smooth, Sway-Free Ride
- Article: How to Choose the Right Trailer Hitch Class
- Article: Brake Controller Installation: Starting from Scratch
- Article: Types of Bumpers
- Article: Which Hitches are Made in the USA