Can I Replace Standard Spindles with EZ-Lube Spindles Without Replacing the Entire Axle Assembly
Question:
I goofed hand packing my standard bearing hubs and ruined them. I want to replace the hub and spindle with an ez lube assembly. Can I do this on the existing axle tube or do I start over with a complete ezlube axle? I have nothing to salvage on the existing hubs.
asked by: George R
Expert Reply:
You can cut off the old spindle and have an EZ-Lube spindle welded on your current axle. I would recommend using the same size spindle, just the EZ-Lube version, as your trailer originally came with.
That being said, new hub assemblies and bearings should be hand greased when first installed. You have to get a good coating on all the bearings first, then you can use an EZ-Lube spindle to fill up assembly and do the packing for you.
You will still have to perform regular maintenance. Dissembling the hubs periodically, cleaning the old grease off the parts and inspecting for heat damage.
I have added a link to a video that shows a typical maintenance routine with an EZ-Lube spindle trailer.
Product Page this Question was Asked From
Easy Grease Trailer Hub and Drum Assembly for 3.5K Axles - 10" - 5 on 4-1/2 - Pre-Greased
- Trailer Hubs and Drums
- Hub with Integrated Drum
- Easy Grease
- EZ Lube
- Pre-Greased
- L68149
- L44649
- For 3500 lbs Axles
- 1/2 Inch Stud
- 5 on 4-1/2 Inch
- 13 Inch Wheel
- 14 Inch Wheel
- 14-1/2 Inch Wheel
- 15 Inch Wheel
- etrailer
more information >
Continue Researching
- Shop: Dexter Trailer Hub and Drum Assembly for 4,000-lb E-Z Lube Axles - 10" Diameter - 5 on 4-1/2
- Shop: Dexter Trailer Hub & Drum Assembly for 3,500-lb Axles - 10" Diameter - 5 on 4-1/2 - Pre-Greased
- Article: Most Popular Wheel Bearings
- Video: Review of etrailer Trailer Hubs and Drums - Hub with Integrated Drum - AKHD-545-35-EZ-K
- Search Results: brake drum
- Shop: Trailer Hub and Drum Assembly - 3,500-lb Axles - 10" Diameter - 5 on 4-1/2 - Pre-Greased
- Shop: Dexter Trailer Hub and Drum Assembly for 3,500-lb Axles - 10" Diameter - 5 on 4-1/2
- Search Results: k08~247~94
- Search Results: axle nut retainer
- Search Results: dexter 8~247
- Q&A: Replacement Hub and Brake Assembly Recommendation for Al Ko Hub 363219
- Shop: Easy Grease Trailer Hub and Drum Assembly for 3.5K Axles - 10" - 5 on 4-1/2 - Pre-Greased
- Shop: Dexter Trailer Hub and Drum Assembly for 3,500-lb E-Z Lube Axles - 10" Diameter - 5 on 5-1/2
- Q&A: What is the Torque Spec of the Spindle Nut on a Dexter E-Z Lube Axle
- Q&A: What Is The Recommended Lug Nut Torque On 7,000lb Axles?
- Search Results: trailer hitch ball cover
- Video: Dexter Nev-R-Adjust Electric Trailer Brake Kit Installation
- Shop: Trailer Hub and Drum Assembly - 5,200-lb and 6,000-lb Axles - 12" - 6 on 5-1/2 - Pre-Greased
- Search Results: dexter never lube axles
- Q&A: Is it Normal For Trailer Axle to Not have Grease Fitting
- Q&A: Will etrailer Hub and Drum # AKHD-545-35-K Fit an ALKO Axle
- Q&A: Will Trailer Hub and Drum # 84546UC3-EZ Fit an ALKO 3500 Pound Axle
- Q&A: Can 3500 lb AL KO Brake Assemblies be Replaced with Dexter Brake Assemblies
- Search Results: 10 inch brake drum
- Video: Dexter Nev-R-Adjust Electric Trailer Brake Kit Installation - 5th Wheel