Dimensions of Bulldog Square Jack with Footplate BD180455
Question:
Hello I am considering using the BD180455 jack on a project and I need more dimensional specs to see if it will fit where i need to use it. Thanks
asked by: Andrew G
Expert Reply:
I went to our warehouse and grabbed a sample of the Bulldog Square Jack with Footplate # BD180455 so that I could measure it for you. Since I am not certain exactly what measurements you need I will provide as many as possible that do not already appear within the jack's displayed specs.
Overall length of grey outer tube: 23-inches.
Cross section of grey outer tube: 3 x 3-inches.
Cross section of Inner Tube: 2-1/2 x 2-1/2-inches.
Tube Wall Thickness: 1/8-inch for inner and outer.
Rate of Travel: 10 handle turns per inch of rise or drop.
Foot Plate Dimensions: 8 x 8-1/2-inches.
Overall Height of Retracted Jack and Foot: 25-11/16-inches.
If the above information does not cover all your needs please reply to my email with the additional information you need and I will be glad to provide it for you.
Product Page this Question was Asked From
Bulldog Square Jack w/ Footplate - Drop Leg - Sidewind - 28-1/2" Lift - 7,200 lbs
- Trailer Jack
- Car Hauler
- Enclosed Trailer
- Utility Trailer
- Leveling Jacks
- Tongue Jacks
- Steel
- 7001 - 8000 lbs
- Sidewind Jack
- 29 Inch Lift
- Weld-On
- With Rectangle Foot
- Bulldog
more information >
Continue Researching
- Shop: Square Direct Weld Jack w/ Footplate - Drop Leg - Sidewind - 28-7/8" Lift - 7,000 lbs
- Search Results: siding
- Shop: Trailer Valet JXC Trailer Jack w/ Footplate and Drill Powered Option - A-Frame - Sidewind - 5K
- Q&A: Technical Diagram Of 10000lb Pro Series Square Jack - Drop Leg w/ Spring Return
- Shop: Replacement Female Pipe for etrailer and Ram Pipe Mount Swivel Jacks - 9/16" Pin Hole
- Shop: Replacement Pipe for etrailer and Ram Pipe Mount Swivel Jacks - 2-1/2" - 5/8" Pin Hole
- Search Results: tjdp~5000s~flb
- Video: etrailer Trailer Jack - Side Frame Mount Jack - TJP-7002-B Review
- Shop: Replacement Male Pipe for etrailer and Ram Pipe Mount Swivel Jacks - 2"
- Shop: Square Pipe Mount Swivel Jack w Footplate - Weld On - Sidewind - 15-1/4" Travel - 3,000 lbs
- Shop: Weld-On 2" Diameter Pipe Mount Tube for Pipe Mounted Trailer Jacks
- Search Results: bulldog jack
- Search Results: fender
- Search Results: jack swivel mount
- Video: etrailer Trailer Jack TJP-OP58 Review
- Search Results: 800144
- Article: How to Accurately Measure Trailer Leaf Springs
- Q&A: Recommended 7000lb Leaf Springs To Replace Dexter 072-027-00
- Article: Trailer Wiring Diagrams
- Q&A: Using NOCO 2 Bank Charger With Parallel Batteries in Truck
- Q&A: What are the Dimensions of a #99 Spindle
- Q&A: How To Charge 12v Batteries Wired in Parallel
- Q&A: Replacement Axle For 84 Inch 3,500 Pound Dexter Axle
- Article: Trailer Hitch Receiver Sizes
- Q&A: Replacement Antennas for Voyager WiSight Wireless Backup System
- Article: Stability Control for Heavy Duty Vehicles
- Article: Testing Trailer Brake Magnets for Proper Function
- Article: Replacing RV Awning Fabric: Your Step-by-Step DIY Guide
- Article: Brake Controller 7- and 4-Way Installation Kit (ETBC7)