Trailer Hitch Recommendation for a 2015 Chrysler Town and Country No Fascia Trimming

Question

Question:

The,2015 theres no trimming needed is there

asked by: Jeff

1

Helpful Expert Reply:

When we installed the Curt Hitch part # 13364 on a 2015 Chrysler Town and Country we didn't have to trim the rear fascia. We just let the hitch put slight pressure on the bottom of the fascia and it fit and worked well without trimming. See the install video I attached.

expert reply by: Jameson C

1

Answer 1

For your 2012 Chrysler Town And Country the hitch I recommend is the Curt Hitch, part #13364. This is a Class lll hitch with a 2 inch receiver opening. I have attached an installation video for this hitch on a 2012 Town And Country you can check out.…

view full answer...

Answer 2

The Curt Trailer Hitch Receiver #13364 will accommodate your spare tire on your 2016 Chrysler Town and Country no problem. This is actually designed to fit around Stow-N-Go seats so you should have plenty of room! Attached is an installation video on…

view full answer...

Answer 3

Your 2010 Chrysler Town and Country minivan can be equipped with either a 1-1/4-inch Class II or a 2-inch Class III trailer hitch. All options are shown on the link provided. I suggest the Class III hitch #13364 from Curt; this is the most popular…

view full answer...

Answer 4

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 5

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 6

There is only one difference between the Curt Trailer Hitch Receiver #C13176 and etrailer Trailer Hitch Receiver #e98909 that fit your 2020 Chevrolet Colorado, which is the finish. The Curt trailer hitch has a glossy black finish while the etrailer…

view full answer...

Answer 7

Class I and Class II hitches both have a 1-1/4 inch receiver opening. The difference is that a Class I hitch has a lower tongue weight rating, usually 200 pounds and a lower towing rating, usually 2,000 pounds. A Class II hitch usually has a tongue…

view full answer...

Answer 8

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 9

Yes, we do. To add a hitch to your 2024 Toyota Grand Highlander, I recommend the Curt Trailer Hitch item #C26VV. This hitch is custom fit and bolts to your Toyota with included hardware. This is a class III hitch with a 2" receiver. It has a…

view full answer...

Answer 10

Yep, so long as your 2024 Subaru Crosstrek Wilderness is not a hybrid both the Curt and etrailer hitches will fit: - Curt Trailer Hitch Receiver #C13382 - etrailer Trailer Hitch Receiver #e98912 The only difference besides price is the finish; the…

view full answer...

Answer 11

As far as wiring for the 2024 Toyota Grand Highlander, we do have the Curt #C59236 available which is more of a universal hardwire harness. Unfortunately there are not any plug-and-play options that have been confirmed to fit as of yet (October 4,…

view full answer...

Answer 12

To add a class III hitch to your 2024 Honda CR-V hybrid, I recommend the Curt Trailer Hitch item #C13397. This hitch is custom fit and bolts to your CR-V with included hardware. It is a class III hitch with a 2" receiver. I really like this…

view full answer...

Trailer Hitch Recommendation for a 2015 Chrysler Town and Country No Fascia Trimming

Product Page this Question was Asked From

Featured Help Information

Instructions

Miscellaneous Media

Continue Researching