Can Two Different Hubs that Use the Different Bearings Be Used on Same Trailer Axle
Question:
As long as the hubs or drums I am using accept the correct bearing race, is it ok to use a hub assembly with the 15123 outer bearing on one side of the axle and a hub assembly that uses LM67048 on the other side of the axle using the same #42 spindles? Thanks,
asked by: Rob D
Expert Reply:
The # LM67048 and the # 15123 both have the same inner diameter of 1.250 inches. So in theory they would both work on the same spindle. It sounds like you are thinking about using two different hubs on your trailer axle. As long as the hubs both use bearings and seals that fit the spindle they are used on you would be fine.
Products Referenced in This Question
Replacement Trailer Hub Bearing - 15123
- Trailer Bearings Races Seals Caps
- Bearings
- Standard Bearings
- 1.250 Inch I.D.
- Bearing 15123
- Race 15245
- 5200 lbs Axle
- 6000 lbs Axle
- 7000 lbs Axle
- etrailer
more information >
Product Page this Question was Asked From
Replacement Trailer Hub Bearing - LM67048
- Trailer Bearings Races Seals Caps
- Bearings
- Standard Bearings
- 1.250 Inch I.D.
- Bearing LM67048
- Race LM67010
- 5000 lbs Axle
- 6000 lbs Axle
- etrailer
more information >
Continue Researching
- Video: Review of Dexter Trailer Hubs and Drums - Idler Hub - 8-213-51
- Q&A: What Are the Specifications of the Dexter Trailer Idler Hub 008-445-15
- Q&A: Replacement Galvanized Hubs For Dexter 8-213 on 5,200 lb Axle
- Shop: Dexter Trailer Idler Hub Assembly for 6,000-lb E-Z Lube Axles - 6 on 5-1/2 - Galvanized
- Search Results: 15123 bearing
- Search Results: dexter trailer hub
- Search Results: boat trailer axle kit
- Search Results: dexter hub
- Video: Dexter Axle Trailer Hubs and Drums - Hub - 8-213-51UC1-EZ Review
- Shop: Replacement Trailer Hub Bearing - 15123
- Shop: #42 E-Z Lube Spindle w/ Flange for 5.2K to 7K Trailer Axles - 2-1/4" Diameter
- Shop: Trailer Idler Hub Assembly for 6,000-lb Axles - 6 on 5-1/2 - Pre-Greased
- Shop: Grease Seal - Double Lip - 2.250" ID - 3.376" OD - GS-2250DL
- Shop: Dexter Trailer Idler Hub Assembly for 5,200-lb Axles - 6 on 5-1/2
- Shop: Kodiak 12" Hub-and-Rotor Assembly - 6 on 5-1/2 - Dacromet - 5,200 lbs to 6,000 lbs
- Video: Powerbuilt Tools - Vehicle Tools - ALL648591 Review
- Search Results: master cylinder cap
- Search Results: dexter brake cylinder
- Search Results: brake actuator parts
- Article: Replacing the Bearing, Races and Seals on a Trailer Hub
- Video: etrailer Hub And Drum Assembly Installation
- Shop: Brake Controller
- Shop: Trailer Wiring
- Q&A: Weight Capacity of Flatbed Trailer with Dual 2-3/8 Inch Diameter Axles
- Q&A: Standard Grease/Dust Caps Won't Fit Hubs on Trailstar Boat Trailer
- Q&A: How To Tell If I Have An EZ Lube Axle
- Q&A: What Hub Has a 5 on 4 1/2 Bolt Pattern That Works with Timbren Axle-Less Systems
- Q&A: Looking for Grease Cap With OD Slightly Larger than 1.98 Inches
- Article: Parts Needed to Add Electric Drum Brakes to a Trailer
- Article: Parts Required to Add Electric Over Hydraulic Drum Brakes to a Trailer