Adding Additional Taillights to 6 by 10 Utility Trailer
Question:
I am installing a second set of trailer lights higher on the back of my 6 by 10 ft utility trailer. Can you send me a wiring diagram to do this, and can they be wired directly off of the existing taillight wires.
asked by: Jerry B
Expert Reply:
I don't have a wiring diagram specifically suited to what you're wanting to do, but I can certainly explain how to wire the additional lights.
If you're wanting to add the # STL78RB lamps, the red wire taps into the turn signal/brake circuit, the black wire connects to the running lamp circuit and the white wire grounds to the trailer frame. You may tap into the existing trailer taillight circuits. Since these are LED taillights, the additional voltage draw will be minimal.
For your existing taillights, using a circuit tester like part # PTW2993 would make identifying what taillight circuit serves which function easier.
I'll also link you to our trailer wiring FAQ article, which you might find helpful.
Products Referenced in This Question
Product Page this Question was Asked From
Optronics LED Trailer Tail Light - Stop, Turn, Tail - Submersible - 10 Diode - Oval - Red Lens
- Trailer Lights
- Tail Lights
- Stop/Turn/Tail
- Oval
- Surface Mount
- Submersible Lights
- LED Light
- 6-1/2L x 2W Inch
- Red
- Optronics
more information >
Continue Researching
- Search Results: weld on spare tire mount
- Q&A: What Size Trailer Rim Should be Used for a 205/75-15 Trailer Tire
- Shop: Trailer Hitch
- Article: Trailer Wiring Diagrams
- Shop: Curt Trailer Hitch Receiver - Custom Fit - Class III - 2"
- Shop: Spare Tire Carrier - Horse Trailer
- Q&A: Which Wires Should be Tapped Into When Adding Additional LED Marker Lights on a Boat Trailer
- Shop: Hook Probe Circuit Tester
- Video: Redline Spare Tire Carrier - Gooseneck Mount - 413200 Review
- Search Results: st17580r13
- Search Results: lug wrench
- Q&A: Difference Between Conventional and Modular Trailer Wheels
- Shop: etrailer Hitch Receiver and Coupler Lock Set - 2" Hitch - 1/2" Coupler Latch - Keyed Alike
- Search Results: weld on spare tire carrier
- Q&A: Wiring in an LED Work Light and Switch to a Trailers Running Light Circuit
- Video: Review of Dexstar Tires and Wheels - Wheel Only - AM20428
- Video: Dexstar Tires and Wheels - Wheel Only - AM20427 Review
- Search Results: trailer light kit
- Q&A: How To Power Third Brake Light On Camper Shell Using 7-Way Trailer Connector
- Shop: LED Combination Tail Light Kit for Trailers under 80" Wide - Submersible - Driver and Passenger
- Search Results: 7 pin trailer light kit
- Video: Kenda Tires and Wheels - Tire with Wheel - AM3S060 Review
- Video: Review of Kenda Trailer Tires and Wheels - Tire with Wheel - AM31952
- Video: Redline Telescoping Lug Wrench with Reversible Sockets Review
- Search Results: spare tire mount for trailer
- Shop: Kenda 215/60-8 Bias Trailer Tire with 8" White Wheel - 4 on 4 - Load Range C
- Shop: Kenda 5.70-8 Bias Trailer Tire with 8" White Wheel - 4 on 4 - Load Range D
- Shop: Trailer Wiring
- Video: CE Smith Spare Tire Carrier - Frame Mount - CE22007Z-11050-2 Review
- Shop: Brake Controller
Douglas B.
4/30/2020
I have 2018 Crusader Primetime 297RKS fifth wheel. Want to put a 2nd set of tail lights higher up. Back wall is solid, so cant run wire in cavity. Would like to tie into bottom original tail lights and run wire up outside to top new tail lights then caulk where I drill hole in plastic. Also, something to cover the wires that run outside. Not opposed to a bar led type if can be done. And not opposed that 2nd set of tail lights are just above presents. Really want more visability from the back. with ladder, bike rack and spare tire, present lights are obsqure. thanks,