20 Amp Circuit Breaker in ETBC7 Installation Kit Keeps Clicking
Question:
Hello, I recently installed a universal wiring control harness that I purchased from you guys and I am experiencing a clicking sound coming from the 20 amp circuit breaker, ive double checked all of my connections and everything appears to be connected properly its been fine for the past several months but all of the sudden Ive been hearing a clicking sound coming circuit breaker under the hood. Any recommendations would be appreciated and thank you for your help.
asked by: John
Expert Reply:
The clicking sound you are hearing is likely from the 20 amp circuit breaker resetting after being tripped. This would indicate that something is shorting out and pulling too much amperage causing the breaker to trip.
Check for any corrosion on the circuit breaker and where it is wired to the battery. You will also want to inspect the wiring leading to the brake controller black wire from the circuit breaker.
What can happen is if you ran the wire through the firewall of the vehicle, over time the wire could have been damaged, especially if you had to drill a hole to run the wires. If the wiring insulation was penetrated then the wire inside could be touching bare metal and causing a short.
Also it wouldn't be a bad idea to check the vehicle and trailer side connectors to make sure they are clean and free of corrosion inside where the wires attach and outside on the pins.
Product Page this Question was Asked From
Universal Installation Kit for Trailer Brake Controller - 7-Way RV and 4-Way Flat - 10 Gauge Wires
- Accessories and Parts
- Trailer Brake Controller
- Installation Kits
- etrailer
more information >
Featured Help Information
Instructions
Continue Researching
- Shop: Trailer Wiring
- Video: etrailer Trailer Brake Controller Kit Installation - 2011 Toyota Sienna
- Shop: T-One Vehicle Wiring Harness with 4-Pole Flat Trailer Connector
- Shop: Universal Installation Kit for Trailer Brake Controller - 7-Way RV and 4-Way Flat - 10 Gauge Wires
- Shop: Brake Controller
- Q&A: Trailer Tow Package For 2011 Toyota Sienna
- Q&A: What is the Correct Trailer Wiring for a 2011 Toyota Sienna with Towing Prep Package
- Video: Trailer Wiring Harness Installation - 2011 Toyota Sienna
- Shop: Redarc Tow-Pro Liberty Brake Controller - Dash Knob - 1 to 2 Axles - Proportional
- Article: Adding Electric Over Hydraulic Disc Brakes
- Q&A: Trailer Wiring Harness Options for a 2011 Toyota Sienna
- Q&A: Parts Needed To Add Brakes To 2011 Jayco Jay Series 10 Sport Pop-up Camper
- Q&A: Do All Trailer Wiring Harnesses for 2011 Toyota Sienna Store in Rear Cargo Storage
- Q&A: Troubleshooting 7-Way Install on Trailer and Brake Wont Work
- Q&A: Recommended Hitch for Best Ground Clearance on 2011 Toyota Sienna
- Video: etrailer Behind the Scenes with the Universal Installation Kit for Trailer Brake Controllers
- Video: Review of Redarc Trailer Brake Controller Parts - Universal Wiring Harness - RED69FR
- Video: Tekonsha Custom Fit Vehicle Wiring - Trailer Hitch Wiring - 118498 Review
- Video: Reese Hitch Ball 58117 Review
- Video: etrailer Trailer Brake Controller Universal Kit Review
- Shop: Metal Loom Clamp - 1/2"
- Shop: Curt Easy Mount Bracket for 4- or 5-Way Flat and 6- or 7-Way Trailer Connectors - 2" Hitch
- Shop: etrailer Electric Trailer Brakes - Self-Adjusting - 10" - Left/Right Hand Assemblies - 3.5K
- Shop: 12 Gauge Black Primary Wire - per foot
- Search Results: 11755
- Search Results: hitch ball grease
- Search Results: dw05745
- Search Results: 6565
- Search Results: 18136
- Search Results: swc8055