Will the Softride Dura Folding Bike Rack fit a Curt # 13354 Hitch on a 2007 Acura MDX
Question:
Will this bike rack fit a Curt Trailer Hitch 13354 on a Acura 2007 MDX? Thanks
asked by: Wayne
Expert Reply:
The Softride Dura, part # SR26247 will fit the Curt Hitch, part # 13354 just fine. You will need to take one measurement however, to make sure the bike rack comes out far enough to clear the bumper.
Measure from the hitch pin hole, straight out to the furthest point of the bumper. As long as this measurement is 6 inches or less, the bike rack will fit.
At the bottom of the Dura page, you will see a few dimensional diagrams that will help you get an idea of how it will fit on your MDX. You can use either of the hitch pin holes on the shank.
If you were also planning on towing at some time in the future, you might also need the following:
Trailer wiring harness, part # 118424
Ball mount, part # 2923
1-7/8 trailer ball # 19260
2 inch trailer ball # 19247
Hitch retaining pin and clip, # PC3
Locking hitch pin, # 40107
For install details and videos, click the provided links.
Products Referenced in This Question
T-One Vehicle Wiring Harness with 4-Pole Flat Trailer Connector
- Custom Fit Vehicle Wiring
- Trailer Hitch Wiring
- Powered Converter
- Custom Fit
- 4 Flat
- Tekonsha
more information >
Curt Trailer Hitch Receiver - Custom Fit - Class III - 2"
- Trailer Hitch
- Custom Fit Hitch
- Class III
- 400 lbs TW
- 4000 lbs GTW
- 5000 lbs WD GTW
- 2 Inch Hitch
- 500 lbs WD TW
- Visible Cross Tube
- CURT
more information >
1-7/8" Hitch Ball - 1" Diameter x 2-1/8" Long Shank - Chrome - 2,000 lbs
- Trailer Hitch Ball
- Trailer Hitch Ball
- Standard Ball
- Chrome-Plated Steel
- 1-7/8 Inch Diameter Ball
- 2-1/8 Inch Shank Length
- 1 Inch Diameter Shank
- 2000 lbs GTW
- Class III
- Draw-Tite
more information >
Draw-Tite Ball Mount for 2" Hitches - 3/4" Rise, 2" Drop - 8-1/2" Long - 7.5K
- Trailer Hitch Ball Mount
- Fixed Ball Mount
- No Ball
- 1 Inch Ball Hole Diameter
- Steel Shank - Gloss Black
- Drop - 2 Inch
- Rise - 1 Inch
- Fits 2 Inch Hitch
- 7500 lbs GTW
- Class III
- Draw-Tite
more information >
2" Hitch Ball - 1" Diameter x 2-1/8" Long Shank - Chrome - 7,500 lbs
- Trailer Hitch Ball
- Trailer Hitch Ball
- Standard Ball
- Chrome-Plated Steel
- 2 Inch Diameter Ball
- 2-1/8 Inch Shank Length
- 1 Inch Diameter Shank
- 7500 lbs GTW
- Class III
- Tow Ready
more information >
Pin and Clip for 2" and 2-1/2" Hitches - 5/8" Diameter x 3-1/4" Span
- Hitch Pins and Clips
- Standard Hitch Pin
- Fits 2 Inch Hitch
- Fits 2-1/2 Inch Hitch
- 5/8 Inch Diameter
- 4 Inch Span
- Draw-Tite
more information >