How to Determine What Size Wobble Rollers are Needed to Replace Boat Trailer Rollers
Question:
Where can I find the size of my rollers?They are on a shoreline rd18-21,and where can I buy them
asked by: Kevin
0
Expert Reply:
You will have to go out and measure the rollers you have on your trailer if you are looking for an exact replacement to use. You will want to measure the overall diameter of them plus the diameter of the hole that runs down the middle of them.
For example, the Yates Ribbed Wobble Roller # YR500YW-7P is 5 inches in diameter and designed to fit a 7/8 inch roller shaft.
expert reply by:
Jameson C
0
Product Page this Question was Asked From
Yates Ribbed Wobble Roller - TPR - 5" Diameter - 7/8" Shaft
- Boat Trailer Parts
- Rollers
- Wobble Roller
- 3 Inch Wide
- 5 Inch Diameter
- Thermoplastic - Non-Marking
- Fits 7/8 Inch Shaft
- Yates Rubber
more information >
Continue Researching
- Shop: Yates Ribbed Wobble Roller - TPR - 5" Diameter - 7/8" Shaft
- Video: Yates Rubber Boat Trailer Parts - Roller and Bunk Parts - YR500YW-7P Review
- Shop: Yates Ribbed Wobble Roller - Heavy-Duty Rubber - 5" Diameter - 7/8" Shaft
- Shop: Yates Ribbed Wobble Roller - TPR - 5" Diameter - 1-1/8" Shaft - Blue
- Shop: Replacement Roller for Dutton Lainson Roller Bunks
- Shop: Yates Ribbed Wobble Roller - TPR - 5" Diameter - 1-1/8" Shaft
- Video: Dutton-Lainson Boat Trailer Parts DL203228 Review
- Video: Review of Yates Rubber Boat Trailer Parts - Blue Ribbed Wobble Roller - YR500BW-9P
- Q&A: Wobbler Rollers With 1-1/2" Long Bushing For 1" Shaft EZ Loader Magic Tilt Trailer
- Shop: Trailer Hitch
- Shop: CE Smith Wobble Roller for Roller Bunks - 2-1/2" Diameter - 1/2" Shaft
- Shop: Trailer Wiring
- Shop: CE Smith Wobble Roller Retainer Ring - Zinc-Plated Steel - Qty 1
- Article: Most Popular Wheel Bearings
- Q&A: Using a Weight Distribution System on a Boat Trailer With Surge Brakes
- Q&A: Replacement Wobble Roller Needed with 1 Shaft for Older Boat Trailer
- Q&A: Can Yates Ribbed Wobble Roller # YR500YW-8PEZ Work with 6,000 lb Boat
- Q&A: Most Common Trailer Brake Line Fitting Size
- Q&A: Replacement 12 x 2 Inch Electric Brakes for AxleTek Trailer Axle B12E-02 12-GG
- Q&A: Replacement Gray Fenders for EZ Loader Boat Trailer
- Article: Brake Controller Installation: Starting from Scratch
- Article: Replacing the Bearing, Races and Seals on a Trailer Hub
- Article: Choosing the Right Suspension Kit for Your Truck and Trailer
- Article: Replacement Automotive Lighting
- Article: Boat Trailer Showdown: Bunks vs. Rollers
- Article: Trailer Tire Sizing
Jason V.
6/12/2020
I am looking to make some changes to my floating boat lift. It currently has fixed, hard plastic bunks with center rollers. However, I'm concerned that too much weight from the boat is being put onto the center rollers and the bunk is scratching my boat. Based on my research, I think the best alternative is a wobble roller set up. How do I determine how many rollers or what roller set up is required to hold my 4,000 (fully loaded) boat?