Replacement Swivel Handle Kit Part DL22449 Measurements
Question:
I have an old trailer do not have the mfg of it and need a new Swivel Handle Kit. It measures 3/8inch in diameter, the straight part with the cotter pin hole measures close to 3 inches long. From the center of the cotter pin hole to the open end of the straight meausres 1 7/8 Do you have anything that would would work? It appears part DL22449 is very close but it does not give me the full specs to compare. Thank you for your time
asked by: Sean D
Expert Reply:
I went to our warehouse to get the swivel handle kit # DL22449 to provide you a few measurements to determine if this is the right part for your swivel jack.
From the center of the cotter pin hole to the end of the handle is 1-1/2 inches. This measurement may be a tad to small from what you referenced of 1-7/8. The diameter of the swivel handle is 3/8 of an inch. The length of the handle from the end (end closest to the pin hole) up to the nearly 90 degree angle is slightly over 2-1/2 inches. I included a diagram and short video showing you the measurements.
This kit consists of a replacement 3/8-inch diameter pull pin, spring, washer and cotter pin. Instructions are included.
Another possibility could be # BD500103. It has a diameter of 3/8 inches. The hole center to end of the pin is 7/8 inches.
We just don't currently have a replacement swivel handle with the measurement of 1-7/8 inches.
Product Page this Question was Asked From
Replacement Swivel Handle Kit for Dutton-Lainson Jack
- Accessories and Parts
- Camper Jacks
- Trailer Jack
- Pins and Clips
- 3/8 Inch Plunger Pin
- Dutton-Lainson
more information >
Continue Researching
- Shop: Replacement Swivel Handle Kit for Dutton-Lainson Jack
- Shop: Replacement Swivel Pin Kit for Trailer Jacks
- Shop: CE Smith Trailer Idler Hub Assembly for 3,500-lb Axles - 6 on 5-1/2 - Pre-Greased
- Shop: Replacement Gear Kit for etrailer and Ram Sidewind Jacks - 2,000 lbs and 5,000 lbs
- Shop: Replacement Flange Nut for Dexter Trailer Suspension Kits
- Shop: Dexter Shackle Bolt for Double Eye Springs - 9/16" Diameter - 2-7/8" Long - Qty 1
- Search Results: 63023
- Shop: Channel Tongue Trailer Coupler - Trigger Latch - Zinc - 1-7/8" Ball - Bolt On - 2,000 lbs
- Search Results: lm48548
- Video: Review of Dutton-Lainson Replacement Swivel Handle Kit - DL22449
- Search Results: 337b46
- Search Results: idler hub assembly
- Search Results: 13~104
- Search Results: spindle
- Search Results: eq~104
- Q&A: Replacement Linch Pins for the Roadmaster Stowmaster 5000 Tow Bar
- Q&A: Comparing the Dutton-Lainson Swivel Pin to the Fulton Swivel Pin
- Shop: Ladder Rack
- Q&A: Need Replacement Pull Pin Kit for Dutton-Lainson Swivel Jack on Midwest Trailer Model SLXR2314LW
- Shop: Tailgate
- Shop: Trailer Wiring
- Shop: Suspension Enhancement
- Video: Dutton-Lainson Trailer Jack Replacement Swivel Pin Kit Review
- Article: Most Popular Wheel Bearings
- Q&A: Bushing and Bolt For Equalizer 13-140-3 Rear Spring Attachment
- Q&A: Recommended Replacement for GC10A-4E Water Heater
- Q&A: Trailer Running Light Fuse Location for 2014 Ford F-150
- Q&A: Direct Replacement Water Heater for Atwood Model GC10A-4E
- Article: Double-Eye Trailer Suspension System Review
- Article: Slipper Spring Trailer Suspension System Review