Torque Specs for the Installation Hardware of the Curt Hitch part # 13364

Question

Question:

What is the spec for the bolts on this install

asked by: Gord M

0

Expert Reply:

The torque specs for the hardware that comes with the Curt Hitch part # 13364 that you referenced are in the installation instructions that I have attached.

Since we link the instructions directly from the manufacturer and they are subject to change we avoid posting the torque figures for liability purposes.

I also attached an installation video for you to check out as well.

expert reply by: Jameson C

0

Answer 1

Thank you for your purchase of the Curt A16 5th Wheel Trailer Hitch #C16120 from etrailer, and the two bolts on the side of the head unit #C16520 should not be coming loose. According to Curt, you should make sure those two bolts are torqued to 175…

view full answer...

Answer 2

When installing the Curt Trailer Hitch Receiver #13322 on your 2005 Chevy Silverado 1500, you will need to torque the rear M14 bolt to 126 lb-ft and all the 1/2 inch fasteners to 110 lb-ft. I have attached an installation video that you can use for…

view full answer...

Answer 3

Your 1999 Dodge Ram 2500 base rails can transfer to your 2001 Dodge Ram 2500 (because they are in the same generation). You will need to get new custom fit wiring #HM42137 (the 1999 custom fit wiring is #C56001) & replacement hardware kit…

view full answer...

Answer 4

The Tow Ready 2 Inch Hitch Ball, part #63845, you have referenced needs to be torqued to 250 foot pounds. It is recommended to frequently check that the ball is tightened to these specifications. If you are meaning the mounting bolts that are used…

view full answer...

Answer 5

Trailer connector #20135 is meant as a replacement for the factory 7-Way trailer connector on a 2002 Dodge Ram. If your truck did not come with a factory 7-Way then this connector will not work. If it does have a factory 7-Way then I think I have a…

view full answer...

Answer 6

When installing the B&W Extend-A-Goose Gooseneck Coupler #BWTEXA4200, the trailer sleeve set bolts should be torqued down to 125 foot pounds. I have attached the complete install manual below that you can also look through.

view full answer...

Answer 7

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 8

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 9

There is only one difference between the Curt Trailer Hitch Receiver #C13176 and etrailer Trailer Hitch Receiver #e98909 that fit your 2020 Chevrolet Colorado, which is the finish. The Curt trailer hitch has a glossy black finish while the etrailer…

view full answer...

Answer 10

Class I and Class II hitches both have a 1-1/4 inch receiver opening. The difference is that a Class I hitch has a lower tongue weight rating, usually 200 pounds and a lower towing rating, usually 2,000 pounds. A Class II hitch usually has a tongue…

view full answer...

Answer 11

Yes, we do. To add a hitch to your 2024 Toyota Grand Highlander, I recommend the Curt Trailer Hitch item #C26VV. This hitch is custom fit and bolts to your Toyota with included hardware. This is a class III hitch with a 2" receiver. It has a…

view full answer...

Answer 12

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Torque Specs for the Installation Hardware of the Curt Hitch part # 13364

Product Page this Question was Asked From

Featured Help Information

Instructions

Miscellaneous Media

Continue Researching