Technical BulletinSUBJECT/Summary: Upon installation of your product, raise the load. If the ratchet pawl is clicking while raising the load, the brake is confirmed as operating properly. If the ratchet pawl does not click, lower the load without letting go of the handle and set the brake.The brake can be set by holding a flat edge screwdriver between the drum gear and the top of the pinion gear and turning the handle slowly in a clockwise motion until the pinion gear rotates freely.This process can be performed after the winch is installed on equipment. Typically this is a once-and-done fix for a perceived functional issue. In the application of your winch, a minimum line load will activate the brake automatically, with each use.
Part Number: K1051 Series, KX1051 Series, K1550 Series, KX1550 Series and K2550 SeriesManufacturer: CequentBulletin Date: 4-18-12
Bulletin Number: TB12-05Updated by: Raymond P.
Last updated: 7/5/18
Lance does have a proprietary plug, but many customers see a standard 6-way or 7-way round and notice it doesn't fit their factory 7-way as well. I've attached an article to help if you have one of the 7-way or 6-way round connectors which we…
The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…
In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.
For sag from towing a trailer the best recommendation I can make is actually a weight distribution system. Suspension enhancement will help level your truck while towing. But the advantage to a weight distribution system is that it levels the vehicle…
The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…
Choosing the right height setting for your 5th wheel hitch is a combination of a few different variables. First of all you want your towing setup to be as level as possible. With your Montana High Country 340BH level you will want to measure from the…
A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…
The difference between an load range C and load range D tire in the same size is the capacity and psi rating. The two tires will still have the same dimensions and fit on the same wheel. The D rated tire has a higher capacity. For a ST175/80D13 like…
Thank you for all of the information! I definitely have some recommendations for you but I do encourage you to get that OEM suspension looked at especially if you think it used to look different prior to your last trip. Any suspension enhancement…
There is only one difference between the Curt Trailer Hitch Receiver #C13176 and etrailer Trailer Hitch Receiver #e98909 that fit your 2020 Chevrolet Colorado, which is the finish. The Curt trailer hitch has a glossy black finish while the etrailer…
Trailer wheel bearings are specific to the spindle that is installed on the axle that is on your trailer. You will need to safely support the trailer, remove the wheel and tire, remove the grease cap, remove the cotter pin and washer that secures the…
Yes, I have listed for your below the roof rack systems from Rhino-Rack, Thule, and Yakima that will fit the RetraxPRO XR Hard Tonneau Covers like part #RTT-80243 for your 2019 Ram 1500. Rhino-Rack Vortex Crossbar System part #RRVA180B-RRRLT600…