Whether you're wrapping up the end of a trip, preparing for the off-season by winterizing, or giving your tank a much-needed cleaning, you're going to have to drain your RV's water heater sooner or later. Here's how to remove that pesky plug, not scald yourself, and ultimately empty your water heater. Let's get started! Steps for draining your water heater:
Turn Off RV Water Heater & Power Sources
Relieve Some Pressure with the Pressure Release Valve
Pull the (Drain) Plug
Let it Flow
Watch Now: How to Drain, Clean, and De-Scale Your RV Water Heater
Turn Off RV Water Heater & Power Sources
You don't want to drain your RV water heater tank with scalding hot water inside. So go ahead and turn your interior and exterior water heater switches off and let your water cool. (To make sure it's cool enough to touch, turn on a hot water tap inside the RV and test the temp.) If the water's not cooling quick enough for your liking, reenact that one miserable shower you had by turning on the tap and letting the hot water run out.
Once it's cool and you're ready to work, turn off your water source, your pump, and any tank power sources you might have connected (propane or electric). We want everything shut down and suitably cool for this job!
Turn off your interior and exterior switches!
Relieve Some Pressure with the Pressure Release Valve
Once everything's nice and cool in there, pull your pressure release valve to depressurize the tank.
Pull the (Drain) Plug
This next step is really draining...literally. (I know, I know.) Use a wrench or socket (it's usually a 1-1/16" socket) to remove your water heater drain plug or anode rod. The dam is now open and the water will come flooding out. (I recommend a bucket to catch the flood unless your grass needs some watering.)
Pro tip: if you don't already have the right wrench or socket for the job, I recommend picking up a water heater drain valve wrench and tossing it in your storage compartment with your other RV tools.
I also want to draw attention to the two different plug types: standard drain valves and anode rods. If your drain plug comes out with nothing attached, you've got a standard
valve. If it comes out with a long (probably corroded) rod attached, you've got an anode rod.
Anode rods are most commonly used in steel tanks to help prevent tank corrosion and are pretty common in Suburban heaters. Basically, the aluminum or magnesium anode rod acts as a decoy, drawing the ions that would normally attack your tank walls to itself instead. When you take the anode rod out of your water heater, be sure to thank it for its noble sacrifice.
Note that anode rods only work if there is sacrificial metal left to, well, sacrifice. Once the rod is about 75% corroded, it's time to replace it (usually once a year).
Pictured: A new rod and an old rod. If your anode rod looks like the thing on the right, it's time to replace it. Pictured: A standard water heater drain plug
Let it Flow
Just keep letting it flow until the tank runs dry. After that, you can replace your drain plug and close your pressure relief valve. If all you wanted to do was drain the water heater, then congrats, you can call it quits and go crack open a beer for crossing an item off your to-do list. If you needed to drain your water heater in preparation for cleaning the tank or winterizing your camper, you can check out our help articles on those topics next. (Don't worry, you can still have the beer.)
About Amber S.As a content writer for etrailer, I might spend my morning loading and unloading a bike on five different bike racks to figure out which is easiest to use. I might be in the parking lot, taking pictures of an impressive RV battery setup our techs came across in the shop and discussing the benefits of the setup with the owner. I might spend an afternoon in a manufacturer training classes for some hands-on experience with new products, and then sit down to assemble all this information into a coherent article.
At etrailer, one of our core values is that we are always learning, and I learn something new every day. I start each morning with the goal in mind of taking all of this information and figuring out the best way to answer the questions people ask us (and the ones they don’t know to ask yet), and helping people get the solutions they need to make their lives easier, safer, and more fun. I’m a DIYer at heart, so it brings me great joy to help a fellow DIYer find what they’re looking for, whether that’s a product, an answer, or a community.
If Mercedes installed the factory brake controller harness on your 2016 Mercedes Sprinter Motorhome, it would be under the driver's seat. It would have a green connector. If the harness is not under the seat, then from our experience, it was…
According to my research, if your 2017 Mercedes-Benz Sprinter 2500 came with a factory 7-way trailer connector then you will have the brake controller connector pre-wired. This pre-wired connector should be under the driver side seat which you can…
Technically you can use any T-fitting, including one like the MB Sturgis Sturgi-Stay T-Fitting for POL Valve #103537-MBS before or after your propane regulator. The correct placement and T-fitting is going to depend on what you are trying to hook…
The MB Sturgis Sturgi-Stay T-Fitting part #103613-MBS has type one fittings which are for smaller propane tanks like a 20 lb. The correct t-fitting for a larger 100 lb propane tank which will have POL fittings is the MB Sturgis Sturgi-Stay…
I am not really sure what you are trying to do but you can install a trailer hitch on the rear of a trailer. There are two different kinds of trailer hitches for trailers, frame mount and bumper mount. The frame mount hitches are much stronger but…
Though there may need to be some modifications needed to get it installed, the Progressive Dynamics Inteli-Power RV Converter and Smart Battery Charger - 12V - 60 Amps #PD9260C will work as a good replacement for your WFCO WF-9855. One potential…
The Go Power Industrial Pure Sine Wave Inverter #34278156 has a running output of 2,000 watts. From what I could find researching running washing machines off of an inverter, it is going to depend on the machine and even whether you are using hot or…
For your 1996 Coleman Taos pop-up we do have regulators that will replace your Marshal Gas Controls model 290 2 stage regulator. We have the MB Sturgis Vertical 2-Stage Propane Regulator #108220 and the MB Sturgis Horizontal 2-Stage Propane Regulator…
I'd be surprised if you have a line that has a pressure rating higher than 11 inch water column as that's the standard for camper applications. If you are looking for a new regulator the MB Sturgis Regulator part #108221 is a great solution…
For the humidity, since you have the moisture absorbers, I would recommend keeping your vents closed. There's no way to completely keep the humidity under control but since it's only a month I can't see there being any real issues. As for…
Actually the leaf spring part #e28SR that you referenced would be a perfect choice. It's 1/4 inch shorter than what you currently have which is right what you want as old springs tend to stretch over time as they flatten out.
The Camco Wrench for Screw-In Water Heater Element #CAM09883 is a for the 1-1/2 inch nut and will not work for the anode rod. You will want to replace your anode rod with the Camco RV Water Heater Anode Rod - Aluminum - 3/4" Diameter x…