Your best bet will be to go with the Kats Heaters Engine Oil Dipstick Heater # KH15200. We do not offer an immersion style heater that will work with your 2005 Subaru Outback. The Dipstick Heater, on the other hand, will be a great fit.
Another option is to go with a magnetic heater like the Kat's Heaters Handi-Heat Magnetic Heater # KH1155. The heater itself is 3-5/8" long x 2-1/4" wide and can be attached to the oil pan. view full answer...
The correct Anode Rod is going to be determined by what water heater you have. Unfortunately, your motorhome information does not tell me what water heater you have.
The rod that you were looking at, Camco RV Water Heater Anode Rod # CAM11563 works with Suburban (Mor-Flo) heaters. I have listed out the other Anode Rods that we have available below, along with the water heaters they work with.
- Camco RV Water Heater Anode Rod # CAM11593 (Fits 10-gallon Atwood heaters)
- Camco RV Water... view full answer...
The Replacement Power Cord for Kat's Heaters Frost Plug Block Heaters # KH28500 for the Kat's Heaters Custom Engine Block Heater # KH11483 does not fit your 2014 Ram 1500 with the 5.7 hemi.
Instead, you're going to want to use the Replacement Power Cord for Kat's Heaters Cartridge Style Block Heater # KH28816 for the Kat's Heaters Custom Fit Engine Block Heater # KH11816 instead. view full answer...
Yes, the 5' Long Power Cord w 90-Degree Plug for Kat's Heaters Frost Plug Block Heaters # KH28400 will work with your Kat's Heaters Custom Engine Block Heater - Frost Plug Style # KH11606.
This replacement cable works with Kat's Heaters frost-plug-style engine block heaters, 120V engine block heaters that have 3 prongs, and measures 5' long. view full answer...
The best tankless water heater replacement for your Atwood G6A-7 water heater is the:
Fogatti RV Tankless Water Heater # LSB64FR for white,
Or
Fogatti RV Tankless Water Heater # LSB44FR for black.
Both of these water heaters will fit into your existing cutout for your Atwood water heater, and have a heating capacity of 41,800 Btu. These use propane to heat the water which is standard for this type of water heater as well as all water heaters for RVs. There isn't an exact replacement... view full answer...
The Kat's Heaters Thermostatically Controlled Circulating Tank Heater # KH30115 basically just installs in the lower radiator hose and plugs in when needed. After that you'd just need to plug the heater in and you'd be set.
To install the heater you will first need to drain the cooling system. Then cut the lower radiator hose in the middle of the hose and install the Lower Radiator Hose Connector for Kat's Heaters Circulating Tank Heaters part # KH28115 (included) into the lower hose... view full answer...
The correct replacement water heater for your GC6AA-8 water heater is the Atwood RV Water Heater Item # AT96117. This water is heater is an exact replacement. view full answer...
First be sure the Kat's Heaters Custom Fit Engine Block Heater # KH11812 you received is the correct part as I have seen times where the wrong heater was shipped or possibly returned with and placed in the wrong box. The tag on the heater should corelate to the box for the heater. Next I do see there is a slot and groves on the heater which you will want to verify are positioned correctly inside the hole as this would cause the heater to not fully sit inside when positioned incorrectly.... view full answer...
The Kat's Heaters Thermostatically Controlled Circulating Tank Heater part # KH13150 is confirmed to fit a Dodge Sprinter 2500 from 2007-2009 with the 3.0 diesel engine.
To install the heater you will first need to drain the cooling system. Then cut the lower radiator hose in the middle of the hose and install the 1-1/2" Lower Radiator Hose Connector for Kat's Heaters Circulating Tank Heaters part # KH28115 into the lower hose and secure with two hose clamps.
Locate heater hose along... view full answer...
There is potential for damage to a block heater like the Kat's Heaters Custom Diesel Engine Block Heater part # KH30115 when you start the engine with the heater still plugged in therefore the block heater manufactures recommend against this. That's not to say the element will fail immediately if left plugged in while the engine is on but to minimize failure they do recommend first unplugging. view full answer...
The Foggati tankless water heaters are 100 percent going to be an upgrade over a standard water heater due to their efficiency, as it only uses energy when you turn on the hot water instead of a standard heater that is always using up energy to keep the water hot.
And while it is very likely to fit, we don't have any way of knowing fits of a heater in any specific trailer, so you'll just need to take some measurements for either of the Fogatti heaters, which are the following part numbers:
-... view full answer...
I have a few options for your 2006 Dodge Sprinter 2500 with 2.7L I5 Engine, a block heater like the Kat's Heaters Custom Engine Block Heater part # KH11483 or an engine oil pan heater like the Kat's Heaters Oil or Transmission Pan Heating Pad part # KH24500. I recommend the block heater as it's a custom fit, designed for your exact vehicle whereas the oil pan heater is a universal stick-on type.
I agree that an oil pan heater with direct submersion would be best but this is unfortunately... view full answer...
For your 2015 Chevrolet Colorado, the heater that is a confirmed fit for your vehicle is the Kat's Heaters Custom Fit Engine Block Heater - Cartridge Style - 120V - 400 Watts, # KH11811. I reached out to my contact at Kat's and he said these heaters have a temperature control that is based on the model of vehicle and heater that is application specific. You will want to make sure you get the right heater for your vehicle to prevent issues. view full answer...
The Kat's Heaters Engine Oil Dipstick Heater part # KH15200 is a universal fit item that will work on a variety of different makes and models. There are only two requirements for the dipstick heater to work. The engine oil dipstick opening must be 1/4" in diameter or larger and at least 5 inches of the heating element must be submerged in the oil. The heating element on the above dipstick is 23" long. As most diesel truck engine's use a dipstick much longer than this, I recommend using... view full answer...
I am a bit confused as to what you are asking. Do you have a block heater installed on your 2011 Kia Sorento and simply cannot located the cord to plug it in or do you need a replacement cord for the block heater you have installed now? I don't have any reference to the location of the block heater cord on your Sorento but if you are looking for a replacement cord and you have the Kat's Heaters Custom Fit Engine Block Heater part # KH11812 then you will want to use the Replacement Power... view full answer...
Installing a block heater in your 2014 Hyundai Tucson should take less than 1 hour of labor time. For your vehicle the heater I recommend is the Kat's Heaters Custom Fit Engine Block Heater - Cartridge Style # KH11812 which installs in the Front Left if you have the 2.4L or the Right Rear if you have the 2.0 Turbo Conventional engine.
To install:
1) Locate cartridge hole on the engine block.
2) Clean cartridge hole of all debris. Use compressed air.
3) Attach cord to heater.
4) Install... view full answer...
The Kat's Heaters Handi-Heat Magnetic Heater, part # KH1155 does have an automatic shut-off.
When the engine reaches 275-degrees, the heater shuts off. The heat output for this heater is between 300 and 400 degrees. The heater is usually attached to the oil pan or engine block. view full answer...
According to Kat's Heaters, the Kat's Heaters Custom Fit Engine Block Heater part # KH11812 which is a fit for your 2012 Hyundai Genesis with the 3.8L V6 engine will install in the right hand side on the rear of the engine which is labeled as "RR" in the attached diagram. I have also attached the specified location directly from the application guide for Kat's Heaters.
I am not sure which set of installation instructions you are referring to but the above is the correct location. Once... view full answer...
The Hott Rod RV Water Heater Conversion Kit # DGR10VP is much too powerful for a 6 gallon water heater, and is meant for use with a 10 gallon water heater. Instead, you'll want to use the Hott Rod RV Water Heater Conversion Kit # DGR6VP. view full answer...
The Kat's engine block heater # KH11813 installs in a cartridge hole on the engine block. Once you locate the cartridge hole, clean the hole of all debris. You can use compressed air. You don't need to open the coolant system because the heater installs in the cartridge hole of engine block.
Attach the cord to the Kat's heater # KH11813 and install the heater in the cartridge hole of your engine block and rotate the clip on the cord to secure the heater and cord to the engine block and... view full answer...
Go To Results