The adapter for the Thule HideAway Awning # TH490010 that you referenced that allows it to fit in the top channels of roof rack crossbars is the part # TH490001 which does come with M8 T-Bolts like the part # 853-5715 that you mentioned. If you wanted just T-bolts that fit the # 853-5715 would be what you need. view full answer...
The Kenda Karrier ST225/75D15 Bias Trailer Tire with 15" White Spoke Wheel # AM32545 that you referenced would be the same size and would technically work, but since your trailer currently has radials on it I would recommend you go with a radial instead of a bias ply tire like what this one has.
For that you would want the part # AM32459. This tire is a bit more expensive but it would be your best option. It is highly recommended you use the same tire construction for all trailer tires.
The... view full answer...
For your 2005 Dodge Sprinter, you can use the Thule HideAway Awning - Direct Mount - Waterproof - 55 sq ft # TH490018 or the 80 sp ft # TH490011. There is not a fit for the rain gutter mount you were referring to.
Another option is for roof rack mounting. You can use # TH490010 or # TH490008 with any roof rack crossbars. We do have rain gutter towers for those bars in the Inno roof rack consisting of # INB165 and # INSD. view full answer...
It sounds like you're just looking for a 4-way that you can then connect to the 4 to 7-Way with 4-Way Adapter part # ETBC7 and in which case, you'll need to do a hardwire with a kit like the Hopkins Active Tail Light Converter with Install Kit part # 46255. This kit will splice in behind the tail lights and then allow you to plug into the adapter. If you don't have brakes or a battery then you can leave the blue and black wires on the adapter unhooked, just ground the white wire and hook... view full answer...
To go with Curt trailer hitch # 14250 I recommend etrailer ball mount kit # EBMK2216. It includes a ball mount, a 2 inch ball, a 2-5/16 inch ball (which is probably what you meant since there are no 2-5/8 inch balls), a hitch pin with clip, and a storage bag.
You will also need to add a trailer wiring harness to your Sprinter if it does not already have one. You can use # C59236. I have included links to the installation instructions for the hitch and wiring for you. view full answer...
For what you are wanting from the Hollywood Racks Destination E-Bike Rack # HLY66ZR your best option would be a pivot adapter like the Yakima part # Y02483 as it will give you the additional extension you are wanting as well as gives ability for the rack to swing out and away for rear door clearance like you are wanting. An extender won't allow your rear door style to still open. view full answer...
The Optronics LED Off-Road Light Bar # UCL22CB comes with just basic wiring. The wire is 16 inches long and 16 gauge. The video simply shows us using alligator clips to a power source, but I recommend you use a switch like # EJ-3520-LSW or # PK34513. view full answer...
There are not any Firestone Brackets that are a fit for your Sprinter 3500.
For your suspension enhancement, I recommend the RoadActive Suspension Kit # RAS3620-E. This is a mechanically adjustable system that will allow you to adjust the ride of your Motorhome and give you the additional support you need. This will reduce sway and body roll.
I've linked the page to all your other options if you prefer a jounce style spring. view full answer...
If your 2008 Dodge Sprinter 3500 has a 144 in wheelbase and a factory step bumper, then the Curt Class lll Trailer Hitch, part # 13375 is designed for your van. This hitch has a 2 inch receiver opening.
This hitch has a 5,000 gross trailer weight towing capacity. This hitch is rated for up to 7,500 lbs if a weight distribution system is used.You will want to check your owner's manual or with your dealership to make sure you do not exceed the towing capacity of your van.
If you plan on... view full answer...
The trailer hitch options for a 2007 Dodge Sprinter are different for models with the factory step bumper and models with the standard bumper. The two are not interchangeable so if you have the factory step bumper then you'll need the Curt Trailer Hitch Receiver part # 13358 or if you have the standard bumper then you'll need the Curt Trailer Hitch Receiver part # C13388. view full answer...
There is a top speed rating when driving with tire chains. It is 30 miles per hour maximum unless the vehicle owners manual states that it should be lower, then you must go by the lower speed. We have numerous chain options for a 2006 Dodge Sprinter. I have included a link to the main page for your vehicle. Just click on the correct tire size.
You will not want to drive on bare pavement with chains on the vehicle. If the road is not snow or ice covered, you will need to remove the chains... view full answer...
The trailer hitch I recommend for your 2008 Sprinter is the Curt Adjustable Hitch, part # 13703.
This trailer hitch will work with frames from 22 to 72 inches and the hitch has a 2-inch receiver opening. The hitch can either be bolted or welded on and will work with box frame, C-channel frame, or I-beam frames.
If you plan on doing some towing you might be interested in etrailer ball mount kit # 989900. It comes with 2 ball mounts; one with a 3/4 inch rise or 2 inch drop and one with... view full answer...
The closest tire size we have to what you are looking for is a 175/80-13 which measures 24.1" diameter x 7" wide. This new size will be 2.8" larger in diameter and 1.3" larger in width than the 145/R12 tires that you have now. Please note that only half of this measurement will be applied to the top and sides. Unfortunately, we do not carry any 155/60-13 or 165/60-13 trailer tires nor is this a common trailer tire size.
I recommend the Provider ST175/80R13 Radial Trailer Tire part # TTWTRTM1758013C.... view full answer...
The correct anti-sway bar for a 2013 Dodge/Freightliner/Mercedes Sprinter 3500 regular van or RV cut-away models is going to be # RM-1209-120.
The other one, # RM-1209-131 only fits Class C RV models built on the 3500 chassis. I have also included a link to our FAQ article on heavy duty vehicle stability control for you. view full answer...
The correct SumoSprings Solo Custom Helper Springs for your 2006 Roadtrek SS Agile on a Dodge Sprinter 2500 Chassis is part # SSR-329-47 for the rear and part # SSF-401-54 for the front. These are both easy to install and will work well to provide additional support and help reduce body roll. They are a very popular upgrades for these Class B motorhome conversions. view full answer...
The only way you are going to be able to open the rear doors on your 2007 Dodge Sprinter with a bike rack installed and the bikes attached would be to use a swing-away bike rack. I saw that you were looking at four bike racks so if this is how many bikes you have then I recommend going with the SportRack Ridge Swing 4 Bike Rack part # SR2415 which is currently the most cost effective option that fits the bill. However, you will need the SportRack Bike Frame Adapter Bar part # SR0500 for... view full answer...
Fitting a trailer hitch to a former ambulance can be pretty difficult since the rear bumper area is different than a standard vehicle. That said, I attached an install video and install instructions link to the page down below for you to check out to see if the Curt hitch part # 13358 could potentially fit or not. view full answer...
The correct rear anti-sway bar for your 2013 Sprinter 3500 would be the Roadmaster Anti-Sway Bar part # RM-1209-131. You will need to remove your old sway bar before you can install this product since they utilize the same installation points.
The part # RM-1209-131 that you referenced is for older model Sprinters and gets installed in conjunction with the factory bar but would not work for you since it is for older model Sprinters. view full answer...
Because an ambulance will have a lot of equipment and in it and the the weight of people, the stock suspension will be compressed already. This can lead to the rough ride you described. Adding a Timbren system like # TMBRSP25 for a 2006 Dodge Sprinter 2500 or # TMBRSP35 for a 3500 will reduce the stress on the factory suspension and absorb road shock and reduce roll. This will provide a much better ride.
Both sets have a capacity of 8,600 pounds and are made of rubber. I have included... view full answer...
When installing the Roadmaster Split Bushing for Anti-Sway Bar part # RM-205249-10, I recommend using the Mystik JT-6 part # L74FR. This is a marine grease that is very similar to what comes with their sway bars. view full answer...
Go To Results