As you already have the Furrion Vision S Wireless RV Backup Camera System # FOS07TASF you simply need the LED Marker Light RV Side Cameras # FCE48TASL. view full answer...
Hey Kevin, it looks like the pre-wired bracket on your camper is the "shark fin" style bracket. This bracket is made specifically for the Furrion Vision S Wireless RV Backup Camera # FCN48TASF. The camera in your other picture is their rear red light camera. You could certainly still use the rear red light camera on your camper, it just would not use the pre-wired bracket.
If you want to use the pre-wired bracket, I do suggest returning the camera you purchased and instead getting the... view full answer...
There may be a way to get the Rear View Safety Backup Camera System # RVS-062710 to work if you have enough wire.
To wire these cameras properly you're going to need to connect the red to power, the yellow to the left turn signal, the brown to the right turn signal, the blue to the back/rear, and the black to a ground.
I'll go ahead and attach a wiring diagram as well for you to check out. view full answer...
For your Voyager WVOM541AP monitor you're going to need the Replacement Antenna for Voyager WiSight Wireless RV Backup Camera System # VO54FR. view full answer...
Hey Matt,
For the passenger's side of the Vision S marker light camera, you do need to replace the whole camera and marker light with the Replacement RV Side Marker Light Camera w/ Night Vision for Furrion Vision S System - Passenger Side # FR28NR. view full answer...
Hey Kathleen, yes the Replacement Shark Fin Camera Mounting Bracket part # FRCBRKT-BL is the part you need. You'll wire up the bracket to the wiring of your current pre-wiring setup and once mounted it would be ready for your camera setup that uses Furrion connections. view full answer...
Unfortunately Damien, I have no way to see exactly what parts are on your 2010 Tiffin Allegro Red Open Road 38QBA. It would be best to pull off your current camera and check for any manufacturer information on the camera. You can also check the connector to see if you have one like the Voyager # VCMS12RGPR or Buyers # BP68FR.
Please let me know what information you find on the camera and if one of the connectors matches what you have. view full answer...
Hey David, so the Wisight kit part # ASA24YR was designed for RVs that were pre-wired for the Wisight camera systems. We have another version that is universal with the part # ASA84YR as well. From what I was able to find on your Conquest it was pre-wired for a Way Interglobal camera kit which we do not carry so you would want the universal Wisight option. view full answer...
The Rear View Safety Multiplexer Box # RVS-501N has 6 pins on the power in plug but nowhere else. The camera plugs are all 5 pin. The monitor cable only works if you have a Rear View Safety monitor. If you have a different system you need # RVS-501N-3 instead. view full answer...
Richard, you're just going to need the7-Way Vehicle Power Adapter for Furrion RV Observation Camera # FR87PR. This adapter will just plug into your 7-way and will act as a connector between the tow vehicle and trailer wiring providing the additional power needed. view full answer...
Hey Dwayne, so the PWM filter part # VGR64VR that you referenced only has to install on the running light circuit of the tow vehicle (newer GM truck) for all of the cameras of the Furrion Vision S part # FR98NR to work fine with it. That is the circuit that powers all of the cameras so once the filter is installed everything is good. view full answer...
Hey Vic, what you would want is a outlet kit that you would wire directly to your vehicle battery like the part # RM-9332. This will wire directly to the battery to give you 12 volts and provide the connection that your Furrion Vision S system requires. view full answer...
Your going to be better off going with the Swift Hitch Wireless Hitch Alignment Camera and Monitor # 04928 as the power wire for the camera on the Hopkins Smart Hitch # HM50002 is only about 18" long. The long wire is only for the monitor. And While you could use a In Bed Plug # 41157 to move the connector further forward while also adding an in bed 7-way to plug your gooseneck in this would be difficult to reach being near the front of the bed when you have the tonneau cover. The Swift... view full answer...
Hey Doug, yes you can install the Furrion Vision S 3 Camera system part # FCE48TASL-05 on a fifth wheel that is not pre-wired. It comes with a mount that you can put on the rear of the trailer and then you'd basically just need to run your running light circuit to each of the cameras and you'd be good. Basically the pre-wiring is just the running light circuit ran to the rear of trailer so it's not a super elaborate deal. view full answer...
Hi Charles,
The screws you have in the picture are the ones needed if you were mounting the camera # FOS07TASF into an already mounted shark fin camera mount. If you don't have a prepped trailer with the mounts already in place then you'll need to pick up some self-tapping screws from your local hardware store in order to mount the shark fin camera mount. Furrion does not provide the mounting screws. view full answer...
Hey David, so the 4.3 inch Furrion Vision S monitor is not compatible with the Furrion Vision S side camera kit part # FCE48TASL. The monitor is small enough they figured it wouldn't be able to display all three views so they made it only work with the 5 inch and 7 inch monitors.
To upgrade to the larger monitor so you can use the side cameras you would want the part # FR97FR for a 5 inch monitor or part # FR47FR for a 7 inch. view full answer...
Yes, you can use the ZIP System Green Roof Sheathing as an underlayment for the Alpha Systems Superflex TPO RV Roof Membrane # AL25CV.
Don't forget to also pick up the Alpha Systems RV Roof Replacement Installation Kit # AL63FJ as well since it comes with all of the parts needed to get the TPO properly installed on your RV! view full answer...
Hey Larry, thanks for providing all that info. It sounds like you are on the right track here, because the Curt TruTrack 4P Trailer Mounted Weight Distribution System # C74RV is a great choice. This system is designed for trailers with a tongue weight between about 700 and 1,000 lbs. It stands to reason that your trailer will be within this range at all times, loaded or unloaded. This is a 4-point system so it will provide superior sway prevention and control.
The # C74RV does include... view full answer...
Hey Dock, the Furrion Chill HE RV Air Conditioner System # FR32PR that you referenced does come with everything needed to install in the roof vent hole you have currently on your Grand Design. You'd only need this part number and you'd have everything needed. view full answer...
Hello Tim. We can definitely set you up with a complete AC system with an Advent low profile unit. We currently do not offer these parts as a package, but you can purchase all of the exact same components separately. To answer your question, yes, the same air handler will work with the low-profile unit. Here is what you will need for the complete AC system:
- Advent Air Low Profile RV Air Conditioner - 13,500 Btu - White # ADV79FR
- Air Distribution Box w/ Built-In Thermostat for Advent... view full answer...