The top linch pins on the Replacement Quick Disconnect Crossbar Assembly # 910021-00 you referenced can be found as a quantity of 2 on our site with part # RM-910024. view full answer...
It sounds like you are looking for the Supertop NX, part # B5472015 which is a replacement top that includes all of the bow hardware, the door surrounds, tailgate bar and windshield channel. The front portion of the roof can fold back, like a sunroof. Door skins are not included.
The # B5112415 you referenced would include the fabric top only, with no bows or hardware and would not have the ability to fold back. view full answer...
I am going to list all the parts that you will need to replace the bearings, races, grease seals, and add Bearing Buddys to your 2002 EZ Loader Boat Trailer. You will need 4 of each item to service all 4 wheels.
Inner Bearing # L68149
Inner Race # L68111
Outer Bearing # L44649
Outer Race # L44610
Grease Seal # 168255TB
Bearing Buddy # BB1980A-SS
A 7-Piece Bearing/Race Installation Set # PTW83020 will help you install all your races. view full answer...
You will need either the Dexter Trailer Idler Hub Assembly for 2,200-lb Axles # 8-259-50UC1 for 8-12" wheels or the Assembly # 8-258-50UC1 for 13-15" wheels. Both these hubs use the 1-1//16" Bearing # L44649 for inner and outer bearings. And they use a Grease Seal # 10-9 (1.50" inner diameter). view full answer...
You definitely do not want to use the # e77SR on your trailer with a 3,500 lb axle. These are rated for a 2,000 lb axle which is well under your capacity. If you need a 26" leaf spring I would not get the # e54SR since they're a bit too short. You're better off getting the # e22YR. This is rated slightly higher at 4,000 lbs but that won't be an issue for the trailer and will likely allow them to last a bit longer. These measure 26" which is what you were looking for. view full answer...
The Bestop Tinted Window Kit # B5812115 can be used to replace the rear window of your 2002 Jeep Wrangler as long as you have either the factory soft top or a Bestop Replace-A-Top. view full answer...
When picking out the correct rise/drop ball mount for a towing setup you sometimes can't get exactly the amount you need. The good news is that if you get as close as you can (in your case within 1/2 inch) you will be fine. So using the hitch ball # 40038 that you referenced with the ball mount # C45240 would be a great choice and would work well for you. view full answer...
All you need to do is to go part # RHK and type in 75193 as your hitch number and then "Add to Cart". Then it will automatically add the correct replacement hardware kit for the hitch you have on your 2003 Jeep Wrangler. view full answer...
I contacted our representative at Bestop to inquire about the Replace-A-Top for Jeep, part # B5112009, for your 1989 Jeep Wrangler.
Our representative at Bestop informed me that part # B5112009 is a factory replacement top and that you would need to obtain hardware from your Jeep dealership.
For a complete replacement top with hardware, we have the Bestop Supertop Soft Top, part # B5159901.
I have linked an FAQ on Jeep top replacement hardware that you may find as a good reference. view full answer...
You will need to replace your AOM713WP monitor with a Voyager RV LCD Observation Monitor # VO34FR. Voyager no longer produces the junction box that you are needing. The new monitor removes the need for the junction box and uses the same 4pin camera connection that you have with your current cameras. You will need to wire in the trigger wires that control each camera activation. view full answer...
Based on the information you have given me you have the Roadmaster Adapter for Jeep D-Ring Bumper Mounts to Roadmaster Motor Home Mount Tow Bars # RM-035 or # RM-035-1.
Since you want to stick with Roadmaster parts, the correct replacement pin is the Replacement Hitch Pin for Roadmaster Jeep D-Ring Bumper Mount Tow Bar Adapters - Qty 1 # RM-910044. This hitch pin is the direct replacement part for the pin that came with the # RM-035 and # RM-035-1. The adapter is designed to fit D tabs... view full answer...
Trailer wiring can't be used in reverse in a flat towing situation. You would need to go with a flat towing wiring kit confirmed as a fit for your 2016 Jeep Wrangler.
For that the Hopkins kit part # HM56200 would be exactly what you need. I attached an install video for this for more info as well. view full answer...
People should never mess with a mans vehicle. For replacement side windows for the rear I have included a link to the options. There are different windows for different soft top roofs but they come in kits. Just one side is not available by itself.
If it is a front window then that is a different story. I have included a link to those options as well. Front upper doors/windows are available by themselves.
If you do not have the type of top specified for your selection you may have to... view full answer...
Both your axles will use the same Grease Seal # 58846. I am going to list all the common replacement parts for each axle so that you have that information.
4,400lb Axle
Inner Bearing # L68149
Outer Bearing # LM67048
Inner Race # L68111
Outer Race # LM67010
Grease Seal # 58846
Brake Assemblies # K23-462-463-00
3,500lb Axle
Inner Bearing # L68149
Outer Bearing # L44649
Inner Race # L68111
Outer Race # L44610
Grease Seal # 58846
Brake Assemblies # 23-468-469 view full answer...
Vent lids are actually very universal so since you have the standard vent measurements and a continuous hinge you can definitely use either part # BV0554-01 or part # BV0534-00 depending on which style you like better.
I have attached installation videos for both lids that you can check out. view full answer...
I have incldued a link to all of the windows that we carry for the 2003 Jeep Wrangler. If you have a Supertop, Replace-a-top, or Sunrider then one of these window sets will work. If you have any other type of top, then there are no windows available. view full answer...
The ComeUp Seal Slim Off-Road Winch # CU295051 that you referenced is designed to attach the standard winch mount that your 2020 Jeep Wrangler would have so this would fit and work well for you. This has a 9,500 lb capacity as well so it matches what you are looking for in that regard as well. view full answer...
I have a solution for you and it looks like the C001478 and C001477 are the arms for a Roadmaster 921-3 MX series base plate kit, which would be the Roadmaster Direct-Connect Base Plate Kit - Removable Arms
Item # 1429-3 for your 2008 Jeep Wrangler. To replace those arms you will need to use the Roadmaster Replacement Arms for Base Plate Kits part # RM-ARMS.
There is a form attached to this page that will need to be filled out and sent in so we can ensure that the parts you're ordering... view full answer...
For a 2010 Wrangler, you would need the Replace-A-Top Window Kit, part # B5812935. The kit is compatible with the factory top.
The Bestop Replace-A-Top window kit you referenced, part # B5812115 is compatible with 1997-2002 Wrangler models only, and would not work for your Jeep. view full answer...
I reached out to my contact at Progressive Dynamics and he said that your WFCO 8735P is an older model panel and so if you want to upgrade you will need a whole new system which will be the 45 amp Progressive Dynamics Mighty Mini AC/DC Panel and Converter/Lithium Charger # PD4045LIKA.
He said that you could potentially use the Inteli-Power RV Converter and Battery Charger # PD9140ALV but the wiring would be more complicated and you'd have an overall better experience with the whole new panel. view full answer...