Expert Answers about Ford Expedition

• If Replacing Complete Coleman of RV AC Unit with Furrion Is Coleman Adapter Needed
• Since you were planning on replacing all of the wiring and system you would not need the wiring conversion since you'd be using the Furrion setup completely like the Furrion Chill HE RV Air Conditioner System - Manual - 13,500 Btu - White # FR52PR. Then for a heat strip, part # FR35SR.
  view full answer...


• Installing The Vacuum Line Fittings For The Demco Air Force One Supplemental Braking System
• The Demco Air Force One Supplemental Braking System w/ Wireless Coachlink - Air Brakes - Proportional # DM26VR has a tee fitting that will require you to cut into the vacuum line to install. If you're wanting to know how to connect the vacuum line to the Air Force One then you will insert the fitting, shown below, into the vacuum line tubing and connect it to the AFO unit. I've attached an installation video where Shane will walk you through the all of these steps to ensure your Demco...
  view full answer...


• Where To Connect Black Wire For A 7 Pole Plug On A 2012 Ford Expedition
• The black wire on the Adapter 4-Pole to 7-Pole and 4-Pole Item # 37185 would be routed and attatched to the battery with a fuse holder on your 2012 Ford Expedition. If you do not have the inline fuse holder I recommend Inline Fuse Holder Item # C58470-1.
  view full answer...


• Does Camco UltraGuard 5th Wheel Cover # CAM45752 Have Side Door Access When Installed
• The Camco UltraGuard 5th Wheel Cover # CAM45752 that you referenced has panels on the side of it that you can zip off so that you can access doors on the side of the camper.
  view full answer...


• How Does the Curt Front Mount Trailer Hitch Mount on a 1997 Ford Expedition
• Yes, the Curt Front Mount Hitch Receiver, # 31049, bolts to the frame of your 1997 Ford Expedition 4x4. This hitch comes with 6 carriage bolts that will be fed through the inside of the frame and out using the fish wire tool. This hitch comes will all of the necessary mounting hardware and installation instructions and does not require any drilling or welding. I have attached a link to the installation instructions for you to check out. I have added a link to an article on hitch installation...
  view full answer...


• What is a Westin Ultimate Bull Bar Used For
• The Westin Ultimate bull Bar # 32-0245 is designed primarily to mount lights, act as a low coverage brush guard, and alter the appearance of the vehicle. It is not designed for any other more strenuous activities.
  view full answer...


• Does Using Tow Modes in Superchips Flashpaq Tuner Increase the Towing Capacity of a Vehicle
• there isn't really a specific capacity or anything when in the various tow modes of SuperChips Flashpaq tuner # SU1845. You are still limited to whatever the truck can tow according to its owners manual. You would also have to follow the programmer's instructions for the correct octane of fuel to use in a given mode. The tow modes make sure that you have the power in order to tow easier but they cannot increase the capacity of the truck.
  view full answer...


• Installing Atwood RV Carbon Monoxide and Propane Gas Detector
• When replacing your existing detector with the Atwood RV Carbon Monoxide and Propane Gas Detector # AT36681 you will not need to disconnect the 12V trailer batteries. It also does not matter which of the two power wires you connect first. The third (black) wire is for ground. I have attached a short video review on this unit that you can also check out.
  view full answer...


• Installation of Brake Controller on 1998 Ford Expedition
• The correct Brake Controller Wiring Adapter for your 1998 Expedition would be part # 3035-P. If your Expedition has the factory equipped 7-way trailer connector as most do, once the controller is plugged into the connector located under the dash, typically next to the OBD connector, the controller should be fully operational and ready to go. If your Expedition has the 4-pole connector, you can adapt the existing trailer connector with the # 37185 adapter. The adapter would plug into the...
  view full answer...


• How to Tap into Transmission Fluid Return Line on a 2012 Ford Expedition for a Transmission Cooler
• The line that you will need to tap into is the transmission fluid return line. The easiest way to determine the return line on your 2012 Ford Expedition transmission is to start the truck, shift into drive but do not go anywhere. After about 15 seconds or so put the truck back in park and apply the emergency brake. Turn off the truck. Out of the 2 hoses attached to the transmission, one should be warmer than the other. The one that is cooler is the return line. You can use radiator adapter...
  view full answer...


• Installing Brake Controller on 2012 Ford Expedition
• The 3035-P is the correct Brake Controller Wiring Adapter for your Expedition. The under dash connector will be gray in color, and can be found behind and to the right of the OBD port, as shown in the installation video I have linked you to. Although the existing plug has 6 terminals, only 4 of them are used. If your Expedition is equipped with the factory 7-way trailer connector, once the controller is plugged in and mounted to the underside of the dash, the install will be complete. If...
  view full answer...


• Installing Hopkins Agility Brake Controller with Adapter # HM47294 in 2002 Ford Expedition
• Thank you for providing the photo of the under-dash wiring on your 2002 Ford Expedition. The brake controller connection port under the dashboard on your Expedition should be located just to the right of your right knee when seated. Unless your vehicle had a factory brake controller installed this connector should not be occupied. To assist you I have linked you to an article that covers the brake controller installation process for Ford vehicles, including your 2002 Expedition. The article...
  view full answer...


• Capacity, Warranty, and Installation of Coil SumoSprings on 2022 Ford Expedition Max Limited
• The Coil SumoSprings Custom Helper Springs # CSS-1168R install in the gaps between the coils on your coil springs. They will wrap around 360 degrees and typically have 1/2" to 1" of overlap. They do not have an actual capacity, and all of them are the same in terms of rating. According to SuperSprings International they will increase the capacity of your coils by 15-30%. However, this does not mean they increase the capacity of your vehicle. This increase and support will reduce the squat...
  view full answer...


• Is There an Install Video of the Curt Hitch 31352 On a 2003 Ford Expedition
• I have attached an install video for you of the Curt Front Mount Trailer Hitch Receiver part # 31352 on a 2007 Ford F-150. This will be very similar to the process you will need to follow on your 2003 Ford Expedition but as we have not had the chance to install this hitch on your exact vehicle, I have no video to send you on this. There is also a set of installation instructions in text form which are attached that you can look over to see if you will be able to install the hitch yourself....
  view full answer...


• Dash Thickness Requirements to Mount Redarc Tow-Pro Elite Brake Controller Remote Head
• The remote head of the Redarc Tow-Pro Elite # RED44FR can be mounted directly to the dashboard, to the center console, or through a spare knock-out switch panel. The Universal Mounting Panel # 331-TPSI-001 can be used on dash panels that are up to 7mm (9/32 inches) thick. If you choose to mount the remote head directly to your dash, or center console, the dash needs to have a thickness of 2 to 3mm (1/16 to 3/32 inches) and have at least 3-1/2 inches of space directly behind it to account...
  view full answer...


• Installing an Electric Trailer Brake Controller on a 2006 Ford Expedition with Factory 4-Way
• The blue wire that you have mentioned could be functional, but you will need to test it. You can test it 1 of 2 ways. First, you can install a brake controller using the vehicle specific harness for your 2006 Ford Expedition. I recommend the Tekonsha P2, # 90885 and the Ford wiring harness # 3035-P. You will plug the wiring harness into the port located under the dash, to the right of the steering wheel, then connect the other end to the back of the P2. With the brake controller plugged...
  view full answer...


• If Zipped Shut Would Cats Be Able to Escape the Rightline Gear SUV Tent with Rainfly # RL110907
• I would say that the Rightline Gear SUV Tent with Rainfly # RL110907 that you referenced is cat-proof. As long as you have the door zipped shut it would take a very angry cat willing to claw it's way out of the tent (which even that would be very difficult), or a very smart cat with opposable thumbs.
  view full answer...


• Does Flashpaq F5 Performance Tuner Monitor Transmission Fluid Temp On 2007 Ford Expedition
• I called my contact at Superchips and asked about the Flashpaq F4 Performance Tuner, part # SU1845. They told me this system does not monitor transmission oil temperature. They told me that the Edge Insight, part # EP84030 has the Transmission Fluid Temp display but it depends on whether your vehicle sends that information through the OBD-ll port the unit is plugged into. You can contact your dealership to see if that information is available or not. The # EP84030 is a monitor only and...
  view full answer...


• Which 2 Inch Hitch Ball is Included with 600 Pound Equal-I-Zer Weight Distribution System
• The Equal-I-zer Weight Distribution System # EQ37060ET does include hitch ball # EQ91-00-6080. It is required to be torqued down to spec according to the owner's manual. You'll need a 1-7/8 inch socket.
  view full answer...


• Brake Controller Wiring Adapter # 3035-P to Install Tekonsha P3 on 2012 Ford Expedition
• In order to install the Tekonsha P3 Brake Controller # 90195 in your 2012 Expedition, you'll need the brake controller wiring adapter, part # 3035-P. The adapter would plug into the tow package port located under the steering column. You might also be interested in a replacement mounting bracket, part # TK5906 which would allow you to quickly remove the controller so you can install it on your other vehicle.
  view full answer...