Expert Answers about Toyota Camry
- Trailer Hitch Recommendation for 2015 Toyota Camry for Bike Rack
- The trailer hitch I would recommend for your 2015 Toyota Camry to carry the Curt 2 Bike Platform Rack # C18085 would be the Draw Tite part # 36540 which is a confirmed fit and would work well. I prefer this hitch over the Curt hitch for your vehicle as it does not require the use of a stabilizer strap like the Curt does with a non-supported load like a bike rack.
I attached an install video for the hitch plus a review video for the bike rack on a similar 2015 Toyota Camry.
view full answer... - Replacement Hitch Pin for a Swagman Bike Rack
- We have the specific pin available in several sets:
If you have a 1-1/4 inch / 2 inch combo shank, you can get a new pin in part # S64031, which will replace your cable bike lock as well. Unfortunately, the combo shank pin is not available on its own.
If you have a 2 inch shank only, you can get a new pin as part # S64027 as a single pin, or with a cable bike lock as part # S64030
view full answer... - Replacement Key for Sport Rack Roof Rack System with Lock Core Number 012
- To replace the key for the 012 lock core on your Sport Rack # SR1002 system, you will want to use the Replacement Key # THKEYN012. This key works for Thule and Sport Rack lock cores with the 012 code on them.
view full answer... - Replacement Passenger Side Mirror with Electric Adjustability for 2010 Toyota Camry
- For your 2010 Toyota Camry the K-Source Replacement Side Mirror - Electric/Heated - Black - Passenger Side # KS70601T has the integrated mirror adjustment motor, but that is not available separately. It has the same footprint as the original factory mirror so you can simply paint it to match your vehicle if desired.
view full answer... - Replacement Key for Sportrack Frontier Roof Rack Locks
- We sure do have the replacement key you need for your Sportrack Frontier rack.
In order to get the correct one you will need to know the key number of your current setup.
If you don't have the key to get the part number from, the lock on the rack should have a number engraved in it that you can use.
Once you know the key number you will need to type THKEYN, followed by the 4 digits you found on the key or the lock and the replacement key will come up for you.
For example, if you have...
view full answer... - Replacement Frame Hooks for Swagman XTC-2 BIke Rack
- For your Swagman XTC-2 2-Bike Platform Rack for 1-1/4" and 2" Trailer Hitches # S64670, you will need either the Replacement Ratcheting Hook for Swagman XTC and XC Series Bike Carriers - Short # P166 or the set # P186.
view full answer... - Fit Kit For Thule WingBar Roof Rack on 2017 Toyota Camry
- Thanks for that information, and the correct fit kit for a Thule WingBar Evo roof rack on your 2017 Toyota Camry is the following:
- Fit Kit for Thule Evo Clamp Roof Rack Feet - 5149 # TH145149
This will fit your '17 Camry with the Evo Clamp Feet for Thule Crossbars # TH710501 and WingBar Evo Crossbars # TH711400 or # TH711420
view full answer... - Recommended Sears X-Cargo Roof Box Mounting Hardware
- I'm not sure what you mean about colors for make and model but it sounds like you have the majority of the straps and brackets and simply need the mounting brackets. I recommend the Replacement Mounting Hardware # SR05587 which has been confirmed to fit the older Sears X-Cargo boxes. Depending on your specific roof rack on your 1999 Toyota Camry, you may need to drill holes for appropriate mounting to the crossbar locations. If you need to adjust the hole locations, I recommend gasket...
view full answer... - Replacement Leveling Leg for 2009 Keystone Montana RV
- I spoke with Lippert and according to them they have a custom set of replacement legs made specifically for the Keystone Montana RV Line.
The specific OEM replacement legs for the Keystone Montana's are Follow Leg # LC178652 and the Lead Leg # LC178653. Because of their unique designs they will be the only ones that fit the Montana. The # LG-179014 will not be a replacement that will work for you. It is important to note that for the Keystone Montana the replacement motor will be # LG-142178.
view full answer... - Recommended Replacement Motor For Lippert Components RV Sliding Electric Steps
- The LCI171317 steps are no longer being manufactured, but I do have great news for you.
The replacement motor that will work with the Lippert steps is part # LC301695. This will work with the single, double, or triple RV electric sliding steps.
view full answer... - Replacement Bolt Recommendations for a # 24715 Draw-Tite Hitch
- You can get a hardware kit for your hitch if you get a Replacement Hardware Kit # RHK and then enter the part number for the hitch that you need when prompted to get the right hardware kit.
But if you wanted to run to the hardware store and pick up 4 M10 x 1.25 x 30 mm bolts and corresponding washers you would have everything you need to bolt up the Draw-Tite Sportframe Trailer Hitch Receiver # 24715 to your 2001 Toyota Camry.
I attached installation instructions for you to check out also.
view full answer... - Replacement Slide-Out Wiper Seal Needed
- It sounds like you need the Side Bulb Push On Wiper Seal for RV Slide Out, # SR38FR. The dimensions are 40' long x 3/4" wide x 2-7/8" tall, cut to the needed length. This is a push in seal for 3/16" flanges.
view full answer... - Can Lippert Shock Kit Fit on I-Beam Trailer Frame
- Ideally the trailer would need to have a flat surface on which to mount the upper bracket of Lippert shock kit # LC281255. Depending on the depth of the I-beam will determine if you'd need to box the frame where the bracket would install or if you wouldn't need to do that.
view full answer... - Replacement Hardware For Draw-Tite Trailer Hitch Receiver on 2007 Toyota Camry
- The Draw-Tite Trailer Hitch Receiver # 36416 for the 2007 Toyota Camry will use the following hardware.
Qty. (4) M10 X 40 X 1.25 CL8.8 Hex Bolt
Qty. (4) 3/8” Conical Toothed Washer
Qty. (2) 1/2-13 X 2.00 GR 5 Hex Bolt
Qty. (2) M10 X 1.25 Hex Nut
Qty. (4) Block 1/4 X 1.50 X 3.00
Qty. (2) 1/2” Lockwasher
Qty. (2) 1/2” Hex Nut
Qty. (2) 7/16 Washer
We do offer a Replacement Hardware Kit for Trailer Hitches # RHK that you can order to receive all the correct hardware that you need. You will...
view full answer... - 2003 Toyota Camry Replacement Wiper Blades
- You are correct that the wiper blades on your 2003 Toyota Camry are not symmetrical, the drivers side blade needs to be 24 inches long and the passengers side needs to be 19 inches long.
If you enter your vehicle information into the fit guide, the wiper blades that are confirmed as a fit for your vehicle are the Michelin Stealth Ultra Windshield Wiper Blades # MCH8524 (driver side) and # MCH8519 (passenger side).
view full answer... - Availability of Replacement Hardware for Draw-Tite Hitch on 2005 Toyota Camry
- Replacement Hardware, part # RHK is available for your hitch. You will need to provide the name of the hitch manufacturer which is Draw-Tite in your case, as well as the part number.
view full answer... - Replacement Gas Strut For Old Yakima Rocketbox Cargo Carrier
- I may have a solution for you, but the Replacement Lid Support for Yakima Cargo Boxes # 8880683 will not work to replace the gas strut on your old Yakima Rocketbox. However, even though they don't carry them as a replacement part any longer, my contact at Yakima was able to tell me that it's just a standard gas strut like you'd find on a truck cab topper window and came with a 35-lb force rating similar to the Taylor Made Marine Gas Strut for Boat Hatches - 10 mm Socket - 30 lb Force -...
view full answer... - Availability of Replacement Keys for SportRack Roof Rack
- We can obtain replacement keys for most SportRack roof racks from Thule. Look on the face of the lock next to the key slot for a 3 or 4 digit number. Take that number, and add the prefix 'THKEYN' for the part number of the replacement key.
So, if the number on the lock is 095, the part number would be # THKEYN095. You'd substitute your key number for the 095.
view full answer... - What Size Bolts Does the Draw-Tite Hitch for a 1998 Toyota Camry Use
- The bolts which secure the Draw-Tite Trailer Hitch Receive part # 36336 to the frame on a 1998 Toyota Camry are as follows:
Hex Bolt M10 x 1.25 x 30mm CL8.8
If you need these, we do offer a complete kit that comes with these and everything else you need to install the hitch, the Replacement Hitch Hardware Kit part # RHK.
view full answer... - What Replacement Key do I Need for Sportrack Lock 018?
- Most of the time, Sportrack products have a letter that precedes the numeric lock code on the lock. This is most likely a "N." If this is the case, the replacement part you need for your # SR1005 is the Replacement Key for Thule Racks and Carriers - N018 # THKEYN018. Since Thule manufacturers Sportrack products, this key will work with your application.
view full answer...
Go To Results