The Reese Goosebox you'll need and be able to fit on your trailer will depend on the actual trailer. In addition to the GVWR of the trailer, which will be used to determine the capacity you'll need (either 16k or 20k), you will need to know the pin box model number- either Lippert 1621, 1117, etc.. We do not have specific information on what pin boxes are used on particular trailers, so you'll want to check the pin box for the spec sticker, which should have the model number printed on... view full answer...
When using the Road Armor cushioned equalizers like the part # LC696740 the recommended wet bolt kit is the part # LC52SV which has bolts and shackle straps that have the correct length and width to fit together. A different kit like the # MR76ZR would work too since the bolts and shackles are the same dimensions but it does come with extra bushings that you would not need. view full answer...
54 lbs. The Roadmaster Comfort Ride Shock Absorbers for Tandem Axle Trailers item # RM-2460 will add 54 lbs to your 2021 Vanleigh Vilano 5th wheel trailer. This tandem axle kit works with 3" diameter 5,200 lbs to 7,000 lbs axles. view full answer...
So the difference is purely in how the two connect to your sewer pipe, which will also tell you which one you need; one will slide into the pipe (the spigot) while the other will slide onto the pipe (the hub):
- Slide Into Pipe: Valterra Waste Valve for RV Black Water Tank - 3" Spigot to 3" Lug # T50A
- Slide Onto Pipe: Valterra Bladex Waste Valve for RV Black Water Tank - 3" Hub to 3" Lug # T50
To secure the valves to your pipe you would just need the Valterra ABS Solvent Cement # A05-0303. view full answer...
Yes, axle spread and wheel base by definition are the same measurements. You will measure from the center of one axle to the center of the 2nd axle to determine what you axle spread is.
This may be difficult as some wheels and covers will make this harder to determine. You can also measure from common points in reference to the axle. Such as the front of the front axle tube to front of the 2nd axle tube or front of front tire to front of rear tire. If you do that you will want to be sure... view full answer...
To replace your Coleman Mach AC unit, I recommend the Advent Air Replacement RV Air Conditioner for Coleman Setup 15,000 Btu - White item # ACCOL150 or item # ACCOL150B in black. I do not have a heat pump for you. None of our replacement AC's for Coleman Mach set ups come with a heat pump or have an add on option like the Coleman 48004-066 which we do not carry.
You can add a heat strip with the Electric Heat Strip for Advent Air RV Air Conditioners item # ACMHD.
These units come with... view full answer...
I have a couple of options for you depending on what kind of bumper your Vanleigh Beacon 5th Wheel has. If you have the 2" x 4" bumper, that is not a c channel, the easiest way to add a hitch is to use the Curt RV Bumper Hitch item # C19101. This hitch simply bolts to the bumper and provides you with a 3,500 lbs towing capacity and a 350 lbs maximum tongue weight.
The other option is to install a universal hitch like the Curt Adjustable Trailer Hitch item # 13703. This hitch can be welded... view full answer...
The Roadmaster Comfort Ride Leaf Spring Suspension Kit w/ Shocks - Tandem 8K, 3-1/2 inch Axles # RM-2470-2580 will work on your 2020 Vanleigh Beacon if you have 8,000 pound 3-1/2 inch round axles.
The leaf spring suspension kit prevents shock transfer between axles, increasing traction while braking by as much as 70 percent. This system helps reduce bouncing, and chucking of your trailer. The nitrogen-charged shock absorbers help limit up-and-down motion of the trailer on both compression... view full answer...
Since you have 8K 3" axles you'll just need the Roadmaster Comfort Ride Leaf Spring Suspension Kit w/ Shocks - Tandem 8K, 3" Trailer Axles # RM-2460-2580.
The 3-1/2" requirement you were getting with the # RM-2470-2580 was simply because of the shock kit. I do recommend replacing your U-Bolts as well though with ones like # APUBR-9 as these get stretched and worn out after being torqued down and could potentially cause an issue down the road. These U-Bolts fit a 3" axle with 1-3/4" or... view full answer...
We have a really great kit that comes with everything you'd need to convert your 2021 Vanleigh Pinecrest 335RLP from tandem 6k drum brakes to electric over hydraulic disc brakes with the HydraStar Disc Brake Kit w/ Actuator for Triple Axle Trailers # HSE7K-TR1. This gives you the best braking and actuator components with all brake lines needed as well. view full answer...
The replacement motor will depend on the color of the support arms you have on your Lippert 1917771 stabilizer jack. If the arms are black then you need the C-800 Replacement Klauber Motor for Standard Lippert Electric Stabilizer Jacks # LC138445. If the arms are yellow then you need the Replacement Electric RV Stabilizer Jack Motor for Lippert Landing Gear - Rear # LC352338. These use the existing hardware for installation. view full answer...
I reached out to Swagman for you, who said the distance from the center of one wheel tray to the center of the opposite wheel tray is 9-1/2 inches on the Swagman E-Spec Electric Bike Rack # S94FR.
This has about 19 inches from the center of it's hitch pin hole out to the center of the nearest bike tray. You can use that dimension on your RV to determine if this could fit without an extender. We don't recommend using a hitch extender though as it cuts the capacity of the hitch it is installed... view full answer...
Yes - the Hollywood Racks RV Rider Bike Rack for 2 Electric Bikes - 2" Hitches # HLY64FR is the same as model HR1700. We here at etrailer usually have different part numbers than the bike rack manufacturer.
With the ladder at the middle of your 2022 Grand Design Reflection 341RDS, there is a way to know for sure if the rack does not interfere with the RV Rider when folded up. The measurement you need to conduct is from the center of your hitch pin hole to the furthest outward point of... view full answer...
The best option to smooth out the suspension of your RV that has tandem axle 8k Lippert springs is the Roadmaster Comfort Ride Shock Kit for 8k axles part # RM-2470 which was designed for your axle diameter and capacity. This would do a better job than a Timbren Silent Ride but worth nothing is that Timbren does not offer a kit for 8k axle replacements.
Dampening the suspension movement will do the most to make the ride quality smoother which is what a shock kit does. view full answer...
Definitely a smart idea to replace your Atwood heater with a tankless unit, as they are much more energy-efficient and quicker to heat your water. We do have an option that will easily fit in place of your 16" x 15-1/2" x 20-7/8" Atwood GC10A-4E, which is a unit from Furrion, and it will require the correct size access door as well:
- Furrion RV Tankless Water Heater # FR93FR
- Access Door for Furrion RV Tankless Water Heater - 18" x 18" # FR73FR
Th Furrion measures 19-3/16" deep x 12-5/8"... view full answer...
For a van conversion, I suggest the MaxxFan Deluxe Roof Vent w/ 12V Fan, Thermostat, and Remote, # MA00-07500K for smoke and # MA00-07000K for white vent cover. These options have a built-in rain shield and a thermostat on the 10 speed fan. This rain shield lets you operate in the fan during inclement weather without the need to buy an additional cover. This a reversible fan so you can either pull air from the van or draw air in. You can either control the fan from the pad located on... view full answer...
If you used a power inverter from a 12 volt power source to power the 120 volt Furrion fireplace part # F30SW15ABL that you referenced it would still function just as well. There would be no difference in heat output. view full answer...
Yes, the Goodyear G114 215/75R17.5 Tire w/ 17-1/2" Lynx Wheel and Sensor part # LH43FR does come with a pre-installed TPMS sensor. It works with TST TPMS monitors such as the Color Monitor for TST TPMS Systems part # TST-507-D-C. That's all that is needed, the wheel/tire/sensor combo and monitor. view full answer...
We've had this question in the past and when we checked with Furrion they told us that they discontinued the oven you have and the replacement parts are no longer available.
The best solution for this would be to replace the oven with a newer model like the Furrion 2-in-1 Gas Oven and Range # FR37KR, which would give you a replacement oven and a new range all in one. It's not a perfect solution but because these ovens have been discontinued it would be the only option available. view full answer...
Go To Results