The etrailer Trailer Hitch Receiver # e98853 which is confirmed to fit all models of the 2018 Toyota Sienna comes with the necessary mounting hardware to install this hitch on your Sienna. I have included a video that shows the installation of this hitch on a 2018 Toyota Sienna and you can see that there are no mounting bolts already present on the Sienna, they use the bolts included with the hitch.
If you are getting the hitch to do any towing, the correct 4-way wiring harness to power... view full answer...
The heavy-duty radiator for the 2019 Toyota Sienna is standard for those models with the factory towing prep package. It looks like the LE trim has the prep package as a standard, but I could not confirm this 100%. Your best bet is to call your local Toyota dealer and find out if your model has the prep package. If you have it, then you have the heavy-duty radiator and cooling fans.
If you're looking for a hitch to use with that prep package, I recommend the etrailer Class III Hidden Tube,... view full answer...
The Curt # C13105 hitch uses six M12 x 1.25 hex bolts along with six 1/2" conical tooth washers as shown in the attached installation instructions.
The replacement hardware can be purchased separately with part number # RHK. Just enter the hitch part number (C13105) and select Curt for the manufacturer, before adding it to your shopping cart.
I definitely recommend using a Nylon Tube Brush - 1/2" # 814092 and spray lubricant to clean any debris out of the frame weld nuts prior to install. view full answer...
Yes, the 40 amp breaker is typically used for the battery connection. This will supply a 12V, 40 amp power source for trailers that need to charge batteries or power electrical systems while in transit.
The 20 amp and 30 amp breakers are used for some brake controller installation. You can also use these in place of the 40 amp if your trailer needs less than 40 amps on that circuit.
Depending on your needs, you may not need a power connection and may not need any breakers. If you write... view full answer...
The K-Source Replacement Driver Side Mirror # KS70136T for your 2013 Toyota Sienna is a smooth black color so it's neither matte nor textured. This specific style is designed in a way that you can paint it to match the current style on your vehicle. I reached out to my contact at K-Source who confirmed this. view full answer...
Yes, the Flex-a-lite Transmission Cooler # FLX400117 does include the 3/8" hose and clamps that you see in the picture.
Product Contents:
1-17 Row Plate Cooler
1-Section of 3/8" Transmission Hose
4-Hose Clamps
2-Threaded 3/8" Barbed Fittings
4-Foam Pads
4-Plate Cooler Anchors view full answer...
The Swagman XTC4 4-Bike Rack part # S64665 does indeed come with locks, both a hitch pin bolt to secure the rack to the receiver and a steel cable to secure the bikes to the rack. I have attached for you a full list of parts that come with. view full answer...
The Replacement Wheel Strap for Swagman G10 and Quad 2+2 Bike Racks # SP494 will indeed include the strap, rim protector, nut, bolt, and an end cap for the bolt as well so no sharp edges are exposed. These will be all the pieces needed to completely replace a strap on your rack. I included a picture of the package contents as well. view full answer...
The Coil-Rite helper springs # F4155 fit inside of the rear coil springs on your 2013 Toyota Sienna. The exhaust is not close enough to cause any problems. Also, the coil springs themselves would also help dissipate any heat. I have included a link to a video showing an example installation for you.
Like you said, the Air Lift springs # AL60732 do come with a heat shield as a fail safe. I have linked a video of this kit as well. The Air Lift system is a good value so if the heat shield... view full answer...
The Classic Accessories Boat Cover by StormPro # 052963889383 has dual rear air vents that reduce inside moisture and ballooning of the cover at high speeds.
This boat cover is designed for weather resistance, mildew resistance, and protection against U.V. damage. view full answer...
There is a tab that will allow you to attach a 7-way connector on the Draw-Tite trailer hitch receiver that fits your 2014 Toyota Sienna, the Draw-Tite Trailer Hitch Receiver # 76112.
This will allow you to attach a 7-way for use when towing a trailer with electric brakes, and to add that to your Sienna you will need the Hopkins Plug-In Simple Vehicle Wiring Harness # HM11143495 with the Universal Installation Kit for Trailer Brake Controller # ETBC7.
You can then use a brake controller... view full answer...
The install hardware and install instructions for the etrailer brand # e98853 Class III hitch can be found in a plastic bag that's placed in the square receiver tube. You should have received 6) M12-1.25x40mm hex bolts and 6) conical toothed washers.
If they can't be found in the receiver tube, let me know and we'll get that taken care of for you. view full answer...
The majority of trailer hitches we sell, including the 2-inch Draw-Tite Max-Frame hitch # 76112, come complete with all required mounting hardware and detailed installation instructions. Those instructions, which are linked for you, include a listing of the tools needed. I also linked for you an installation video showing this hitch installed on your exact same 2017 Sienna.
You only need a wiring harness if you intend to tow a trailer that has lights, or if you want to use any other accessory... view full answer...