Bike racks that are suitable for use on the rear of a trailer or motor home must be built specially to withstand the additional stresses found at the back of such long vehicles. The further from the rear axle the back of the trailer or motor home is the more the lateral and vertical forces that will be applied to the rack. Bike carriers designed for use on automobiles, such as the Thule EasyFold 2 Bike Rack # TH903202, are not suitable for use on a motor home, but we do have solutions for... view full answer...
Yes, there is enough room under the covers for your Dometic Penguin II AC's to install the pair of SoftStartRV Soft Starts # SSR44FR. The main unit comes with a good length of wiring so it does not have to mount where your current electrical components mount and can mount where there is more room. view full answer...
To add a Yakima roof rack to your 2023 Honda CR-V with flush rails you will need the following parts:
Yakima JetStream Crossbars - Aluminum - Black - 50" Long - Qty 2 item # Y00425
SightLine Towers for Yakima Crossbars - Flush Side Rails - Qty 4 item # Y64AR
SightClip Fit Kit for Yakima SightLine and RidgeLine Roof Rack Towers item # Y44UR
This aero bar roof rack system has a 165 lbs capacity. I recommend adding the Yakima Same Key System item # Y07204 to prevent theft.
A great perk... view full answer...
Your 2005 Monaco Knight is built on a Freightline Monaco chassis which we do not carry a quick install harness for to install a brake controller like the # TK90160.
I did a little research and found that there should be a blue wire underneath the dash area that will be your brake output wire that will be run to the six way of the Monaco. You will connect this brake output wire to the brake output wire (blue wire) of your brake controller.
The red wire from the brake controller will be... view full answer...
This is a fairly common concern with the Atwood AC units. The reason the fan stays on is because the thermostat sensor is located in the return air side of the AC. The fan keeps air moving from the RV so that it gets an accurate temperature reading. view full answer...
I can definitely help you replace the AC units on your Duo Therm model # 630035.321 system. However, none of the units we currently offer come with heat pumps. To replace just the rooftop units you'll want the Furrion Chill HE Replacement RV Air Conditioner for Coleman Setup item # FR42PV. This is going to plug into the wiring you have now and would allow you to keep your current thermostat to control it.
If you're needing to replace the entire system, I recommend the Furrion Chill HE... view full answer...
The Draw-Tite Ultra Frame Service Body Trailer Hitch # 41990 you looked at is exactly what I would recommend for your 2000 Monaco Diplomat. There are no bolt-on options for this capacity that will fit your motorhome so a universal weld-on hitch is what you need. This has a max gross trailer weight of 16,000 lbs and a 2" receiver. You will also need the 7" weld-on brackets # 4907 or the 16" # 4916. We recommend taking the hitch to a certified welder for installation. view full answer...
It should be combined since that is standard trailer wiring for a 7-way which is also what's used with flat towing setups. Your only way to know with absolute certainty will be to use a circuit tester like # PTW2992 on all of the pins of the 7-way and then compare that to the 7-way diagram I attached. view full answer...
We do offer a steering stabilizer for the 2002 Roadmaster Class A Motorhome with straight axle, airbags, and 1-3/4 inch tie rod. This can be seen on the included link. We do not offer rear anti-sway bars for your MH.
The Roadmaster Reflex # RM-RBK6-RSSA installs between your steering mechanism and your chassis. The Roadmaster system installs quickly without drilling and includes all hardware.
Roadmaster part # RM-1139-143 that you referenced fits Ford F-53 based chassis only. view full answer...
Some manufacturers do not follow the traditional color codes per function. With that being said, you want to test the 7-wire harness by function with a circuit tester like part # PTW2993. Have someone activate the functions while you test for power at the circuits. I have attached a diagram that shows the pin positions of a 7-way. view full answer...
The step itself for the Replacement Step, Motor, and Switch for Kwikee RV Electric Steps # LC3711361 is not available separately, unfortunately.
To replace the steps you're going to need to buy the entire assembly again with # LC3711361.
I know it's not ideal however since Lippert does not offer that as a replaceable part, this is going to be your only option. view full answer...
Anti-sway bars and steering stabilizers perform different tasks. You would benefit from having both. If you are having a hard time steering and get worn out from driving because you are constantly trying to keep the RV straight then a steering stabilizer would be the way to go.
If you are experiencing side to side roll or sway from winds or passing big rigs then an anti-sway bar would be the way to go. In order to determine which parts will fit I will need to know the chassis manufacturer... view full answer...
Since your 1995 Monaco Dynasty is built on a Roadmaster chassis the correct steering stabilizer is the part # RM-RBK6-RSSA according to Roadmaster. view full answer...
We have the Roadmaster Reflex Steering Stabilizer with Mounting Brackets for Class A Motor Homes, # RM-RBK6-RSSA. The sturdy steel spring on this stabilizer keeps your Roadmaster Monaco in line by constantly working to maintain its position. Mount it between the steering mechanism and the chassis for a tight connection that will minimize wander and correct oversteering. view full answer...
Your 2004 Holiday Rambler Endeavor Class A motorhome is based on the Roadmaster RR8R-series chassis and according to the specs in the owner's manual the RV comes with a factory hitch and factory 6-way wiring.
In this case you can use an adapter to give you a 4-pole trailer connection. The linked page displays several such adapters including Hopkins Endurance Flex Trailer Connector Adapter # HM47320. view full answer...
The best brake controller for your situation is the Prodigy P3 # 90195; it is the most popular model we carry due to its effectiveness and ease of use. It will activate your trailer's brakes immediately in proportion to your motorhome's brakes and offers three different boost levels so you can adjust your braking power.
When wiring the P3 on your motorhome with an exhaust brake that does activate the brake light you do need to test to find out if there is power on the brake switch wire... view full answer...
There is not a replacement 7-way wiring harness that is a custom fit for your 2005 Beaver Patriot Thunder that is built on a Roadmaster chassis; what you will need to do is replace it with a universal connector, the Pollak 7-Pole, RV-Style Trailer Connector Socket w/ Wiring Harness and Mounting Bracket # PK11898. view full answer...
I have a steering stabilizer that will work well on your 2011 Monaco Vesta that is build on a Roadmaster chassis but Blue Ox does not have an option. Instead you'd want the Roadmaster Reflex Stabilizer part # RM-RBK6-RSSA which would fit and work well. view full answer...
If your Holiday Rambler Endeavor has leaf springs, you will want to use part # RM-RBK8. If your Holiday Rambler Endeavor has airbags, you will want part # RM-RBK6. These brackets will work with your motor home and the Roadmaster Reflex Steering Stabilizer # RM-RSSA. view full answer...
Go To Results