The etrailer.com J-Style Kayak Carrier # e98878 is designed to fit on a variety of crossbar styles, including most OEM crossbars. As long as your bars are smaller than 4" wide and between 7/8"-2" thick, the etrailer.com J-Style Kayak Carrier will work on your bars. If you measure your crossbars and they're not within those measurements, let me know and I will work to find you an alternative solution. view full answer...
The overall length of the tray is 95 inches and the width is 48 inches. The deck height is 4-1/2 inches and the lower side rails are 4-1/2 inches and the higher side rails are 8-1/2 inches.
We can certainly get more dimensions for the CargoGlide 2200XL Sliding Tray for Trucks # CG2200XL-9548 that you referenced if needed.
We also have a fitguide info that lists what CargoGlide fits what truck which allows people not to have to measure everything to determine a fit too. view full answer...
When installing the # 9465-56 Hide-A-Goose hitch in your 2016 GMC Sierra 2500HD short bed, a hole must be drilled in the bed of the truck. Mark and drill a 1/4” hole 44-7/8 inches from the rear of the bed forward centered between the two wheel wells.
A hole saw will be used to enlarge the hole to the proper size. I attached an install video that shows how this hitch would be installed in a similar 2015 Chevy Silverado 2500HD as yours. view full answer...
Yes, it will. The Reese Goose Box item # RP85FR will work with the GEN-Y Goosepuck 5" Offset Ball item # GY55XR on your 2022 GMC Sierra 3500. Since your Sierra has the shorter 6-3/4' bed I recommend using it.
I attached a picture below so you can see the offset ball being used. It's got Gen-Y's gooseneck adapter instead of the Reese but it'll give you an idea of how it's set up.
If you don't already have them you will also need the Reese Safety Chain Kit item # RP49151 and Safety Chain... view full answer...
Yes, it will. The PowertraxONE XR Hard Tonneau Cover item # RTX73YR is custom fit and designed for the 2023 GMC Sierra 1500 with a 5-3/4' bed length. I checked with Retrax and there are no compatibility issues with the carbon beds. view full answer...
I pulled one of the Curt Adjustable Width Trailer Hitch Receiver for RVs # 13703 from the warehouse and measured it and found that the cross tube was approximately 68-3/8" in length. Knowing how manufacturers are I'm sure the intended size is 68" since the brackets have a 2" lip and both together would add up to 72". I'm sure if we measured multiple the actual length will vary from 68 to 68-1/2".
The brackets are intended to sit flush up against the inside of the I-beams and have a bend... view full answer...
Since your 2018 GMC Sierra 2500 already has the item # BWGNRK1016-5W Turnoverball system installed, you will want the B&W Companion 5th Wheel Trailer Hitch w/ Slider item # BWRVK3400-5W. This sliding hitch has a 20,000 lbs capacity and will give you 12" of travel for making tight turns.
I have linked a video below so you can see how to get this hitch set up.
To make towing with a 5th wheel easier I recommend adding the Curt 5th Wheel/Gooseneck Custom Wiring Harness item # C56000. This... view full answer...
There's an issue with the Reese M5 item # RP26FR that is easily fixed so it will be compatible with a tonneau cover. The handle that comes with the hitch sticks straight up for some reason. If you change it to the Low Profile Handle for Reese M5 5th Wheel Trailer Hitches item # RP58553 you will have plenty of clearance.
The Reese M5 5th Wheel Trailer Hitch item # RP26FR is compatible with the factory towing prep system in the 2021 GMC Sierra 2500. It will drop right down into the pucks... view full answer...
The B&W Companion OEM 5th Wheel Hitch item # BWRVK3700 fits the GM puck system from 2015 - 2019 trucks.
The B&W Companion OEM 5th Wheel Hitch item # BWRVK3710 fits the GM puck system for 2020 - current trucks.
Both of these Companion hitches have a 20,000 lbs capacity. If your 2021 GMC Sierra 2500 has the factory puck system you will need item # BWRVK3710. view full answer...
I went out to the warehouse and measured the Empire Faucets RV Kitchen Faucet w/ Pull-Down Spout # EM42HR and measured 14-1/2" from the threads to the end of the longer water lines, and 5-1/2" from the threads to the end of the shorter water line.
I have attached an installation video as well as a diagram for you to check out as well. view full answer...
Thanks for the additional information! We do have all the parts necessary to convert your Holsclaw Boat Trailer to disc brakes. I have listed them below along with any installation videos we may have.
Brake Actuator - Demco Hydraulic Brake Actuator w/ Electric Lockout item # DM62VR
Idler Hub for item # L44643 Inner and Outer Bearings - Dexter Trailer Idler Hub Galvanized item # 8-259-50
Disc Brake Kit - Kodiak Disc Brake Kit item # K2R35D
Brake Lines - Kodiak Hydraulic Brake Line Kit... view full answer...
The hardware of the etrailer Motorcycle Carrier w/ Ramp for 2" Hitch # e98873 does not have a torque rating this is because the hardware has nylock bushings in the nuts which prevents them from backing off. So using standard hand tools get the hardware hand tight and you'd be fine. view full answer...
I have a solution for you but they do not offer just the pivot bar for resale. It looks like your 2005 Newmar Mountain Aire came with Kwikee steps. You will need the Replacement Step Frame for Kwikee RV Electric Steps - 25 Series item # LC3658374 to replace your damaged ones. These steps are 24" wide.
I have linked a review video below.
If you have another type of steps go ahead and email me back with the make and model number and I will be happy to find you the correct replacement. view full answer...
The Axle Riser Kit - Single Square Torsion Axle # LC382741 provides a lift of 3-1/2 inches and there isn't a version that provides 6 inches of lift. view full answer...
Based on information I could find for the Kat's Heaters Custom Fit Engine Block Heater # KH11811 I see most people mention they see the engine temperature reach around 40-50 degrees Fahrenheit. So it appears this is the range the heater will turn itself back off. view full answer...
The Bully Black Bull Truck Fuel Tank Door Cover - Stainless Steel w/ Matte Black Powder Coat # BBS-2301 has an outer diameter of 7-1/16"; where the ridges are, measures 5-3/8" but this is a peel and stick cover designed to fit over the factory door. For this reason it won't have a true inner diameter. view full answer...
The tailgate is going to be just as wide and just as tall as your stock tailgate, but the lowered section is 11-1/2inches from the bottom to the top. view full answer...