Assuming your clearance lights are surface-mounted, we do have an option for 2-1/2 inch round, 2-wire amber clearance lights:
- Optronics LED Clearance or Side Marker Trailer Light w/ Reflector - 1 Diode - Round - Amber Lens # MCL0040ABB
These are typically used on trailers, but they do have just the ground and power wire running from them, so you can use them as replacements since yours have the same wiring. I have added a link below to a video review for you to check out as well if... view full answer...
Yes since the Advent Air Replacement RV Air Conditioner for Carrier Setup w/ Start Capacitor # ACCAR150 comes with an adapter to work with your existing Carrier setup, you will still be able to control the furnace as well.
This unit fits roofs 2-1/2" to 5" thick, compatible with ducted and ductless systems, and also includes the mounting hardware. view full answer...
You will most likely need to replace your Atwood carbon monoxide/LP gas detector # AT36681. It has a 7-year lifespan and if it has been in service longer than that it may not function properly. There are several things that the flashing lights could indicate:
Power visual indicator flashing means the detector's power supply voltage is too high or too low.
Carbon Monoxide indicator flashing means the CO alarm is disabled because the alarm is resetting or stabilizing OR the unit has gone... view full answer...
I do have an option for you but I do not believe we have any sort of door latch that will work with the u-shaped striker you have on your trailer. As I am sure you are aware, this is not a standard design. However, what we do have for you is the Lippert Components Standard Baggage Door Latch Kit part # LC317649 which comes with the striker plate that you need. Therefore, this is what I recommend you use. It will most likely take a bit of modifying to replace the u-shaped striker with the... view full answer...
The wireless remote you have now with your Carrier Air V Air Conditioner will not work with the Advent Air Replacement RV Air Conditioner for Carrier Setup part # ACCAR150. This kit is designed to retain only the ceiling vent and thermostat. There is no wireless remote for this setup either so you will just need to use the thermostat. view full answer...
It sounds like the wiring was changed going into the solenoids at the hydraulic pump on your 2007 Damon Daybreak. I would check these connectors as it sounds like they were mixed up if the unit was swapped out. This would explain why your jack positions are all off and why the auto level fails when you try to use it. The system sends power to one jack and when a different jack lifts the camper the internal sensors read an error. view full answer...
We do offer a range of RV exterior ladders that are general-purpose replacements that will work on many trailers and RVs, but none of these is a custom-fit item intended as an exact OEM replacement for any particular unit. RV makers may change ladder suppliers and such items are not usually branded.
All exterior ladders we offer are shown on the linked page, the tallest of which are the Stromberg Carlson 99-1/2-inch models # LA-401BA and # LA-401. For an exact replacement your best bet... view full answer...
We have gotten a question about motor part 5973820 before and the manufacturer, Lippert, has confirmed to us that the correct replacement is the Lippert Components Kwikee Step Motor Replacement Kit # LC379608.
I have added a link to a video review of this part for you to check out. view full answer...
I do have an option for you but the Advent Air RV Air Conditioners like part # ACM135 or part # ACM150 when using the Carrier Adapter Wiring Kit for Advent Air RV Air Conditioners part # ACCARKIT isn't compatible with models that have a heat pump. The only option we can offer would be to replace the Carrier distribution box with the Air Distribution Box part # ACDB and then add the Electric Heat Strip for Advent Air RV Air Conditioners part # ACMHD. view full answer...
The motor and gear of the Replacement Motor for Lippert Electric Coach Step # LC301695 does not have a limited range in the direction it operates. Basically what I mean by that is that it does not require you to install it with either the steps out or in. You can do it in either direction and the motor will work fine. The sensors basically just tell the motor to spin in the correct direction as needed. view full answer...
The Bauer Products Motorhome Door Lock # BA64FR that you referenced could fit your 2006 Damon Challenger 348F but you would have to open up the cut out dimensions a little bit as this is designed to fit the dimensions of 5-1/4" wide x 4-1/2" tall, view full answer...
You definitely can use 2 of the 15,000 Btu Furrion Chill Replacement RV Air Conditioner # FR86PR in place of your Carrier Air AC units, but like you said it won't be directly compatible with your current setup. In addition to the AC units you'll also need 2 of the Multi Zone Controller # FACC12ZA-BL and Multi Zone Wall Thermostat # FR93PR to get the 2 AC units to talk to each other. This setup is also compatible with a furnace.
I'm not aware of a wireless remote option for this setup.
If... view full answer...
The simplest solution would be a telescoping ladder like the part # TE74FR that you referenced. This would store in your RV's storage compartment and would get pulled out and used when needed. This obviously doesn't require any installation so it's basically ready to be used as soon as you get it.
For a more traditional RV ladder we have the Surco part # SP501L which permanently attaches to the rear of the RV. It will need to attach to studs on the roof and on the side wall of the RV. view full answer...
We've checked with Kwikee about the Series 39 steps like you have in the past and for a replacement motor setup they have told us the solution is the part # LC379769. view full answer...
If you have the Kwikee 32 Series Step Assembly on your 1996 Damon Motorhome, the correct replacement motor by itself is part # LC379608. For the motor, linkage, and gearbox you will use the part # LC379145. This kit will actually upgrade your older style motor and control board to the new current style. view full answer...
The Rear View Safety Backup Camera System # RVS-062710 is a really solid option that would give you 4 cameras you could have mounted on your 2007 Damon Tuscany 4072.
The monitor is bigger at 7 inches and the cameras have night vision like you are wanting as well so it would be just what you are looking for.
I attached a review video for this for you to check out as well. view full answer...
It sounds you are looking for the Lippert 4 Point Control Panel W/ Amp Connector part # LC175225. The correct wiring harness to use with this control panel is the Replacement Lippert Components 4-Point Leveling System Control Brain Wiring Harness part # LC178278. I confirmed all of this with my contact at Lippert. view full answer...
Camper leveling blocks like the Camco FasTen RV Leveling Blocks # CAM44515 are a good choice for leveling an RV with dually rear wheels. It is okay to place a leveler under only one of the dually tires but using larger blocks like the Camco # CAM44525 would allow both tires to be nearly
fully supported since they are 17-inches wide. view full answer...
For a 4-pole flat wiring harness for your 2002 Damon DayBreak built on a Chevrolet Workhorse chassis, you can use Tow Ready Kit # 119178KIT. This kit includes the powered converter, a circuit tester to help you identify the wires for connection and the quick-splice fasteners. This harness will combine the separate stop and turn functions on the 4-pole output side. These combined signals will be carried on the green and yellow wires, right and left respectively. view full answer...
For your 1992 Damon Challenger, I recommend the Tekonsha Prodigy P3 Trailer Brake Controller # 90195. This controller is a proportional controller that will allow your trailer brakes to apply at the same time and with the same intensity as you hit the brakes in your motorhome.
You will need to hard wire this controller, and I recommend using the Universal Brake Controller Wiring Kit # ETBC7. You most likely will need the some extra wire found as part # 10-2-1as well. This kit will require... view full answer...